Emulex Printer Server manual BootP, Dhcp and Rarp Parameters, Show TCP/IP Characteristics

Page 44

38 Command Reference Guide

Show TCP/IP Characteristics

Display the printer server’s TCP/IP characteristics.

>Server>> [show list] server tcpip

BootP, DHCP and RARP Parameters

When the Emulex printer server reboots, the default sequence of IP address acquisition is to attempt BootP first; if BootP fails, attempt DHCP; if DHCP fails, attempt RARP.

Use the following three commands will define how many times the printer server will attempt BootP, DHCP and RARP.

Define BootP Parameters

Define how many times printer server will attempt BootP.

>Server>> define server bootp n m [temp]

nEnter the number of broadcast requests (between 0 and 7) to be made if the printer server does not know its IP address. The default is 2.

mEnter the number of broadcast attempts to be made if the printer server IP address is known. The default is 0.

temp	Enter the response in volatile memory only.
	The default is permanent.

Image 44

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide What is a Command? ConventionsFormatting You will notice text boxes labeled Note or CautionCommand Lines PromptsKeywords VariablesQuotation Marks Server set define change server dhcp n m temp defaultOptions Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledHelp Initialize server delay delaymin cancel Logout port portnumPing ipaddress Test portnum count countnumCommand Reference Guide General Commands Entire command crash 300 must be entered to be effectiveDisplay Internal ARP Table Halt Printer ServerBelow MIO Version DelayminInitialize Passwords Update Memory SyncPrivileged Access LogoutSet Privilege Password Change Login PasswordRemote Console Password PasswordNode Commands Show NodeEstablish or Change TCP/IP Nodes Show which nodes are known to the printer serverGateway FacilityDefine NetWare Node Delete NodeRemove nodes from the printer server’s internal node table NodenamePort Commands Show Port CharacteristicsDisplay the characteristics of a specified port Test PortChange Port Access Specify the type of connections access the port can makeChange Port Type Change Line Feed CharacterSpecify the type of terminal or printer connected to a port Control the line feed characterChange Port Speed Show Port Status NETJetBaudrate Server show monitor port portnum status netjet deviceServer Commands Show AlarmsShow console error conditions Define Server NameShow Server Characteristics Show Server ConfigurationDisplay Network Characteristics Show Server StatusSet Console Terminal Port Display the current configurable memory table allocationShow Server Limits Available options are Enable or disable special printer server optionsOther Options Set Prompt Modify SnmpServer set server prompt prompt AccrightEnable or Disable Protocols Enable or disable individual protocolsProtocols Change DomainShow NetBios Characteristics AppleTalkShow Server AppleTalk AppleTalk BackspoofingShow Fonts Add Fonts AppleRemove Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Display the printer server’s LAT characteristics Change GroupsShow Server Server show list server LATNetWare Commands Define PasswordChange Authorized Groups Define NetWare NodeDisplay Characteristics Display the printer server’s Novell NetWare characteristicsChoose Frame Type Server show list server netwareServer define node nodename nfserver Server define server netware required enabled disabledDefine Required Fileserver Adjust Processing Speed Define as Remote PrinterRediscover Interval Server set define change server netware rediscover minutesEnable or disable the NetWare forms function Selecting Bindery Emulation or NDS ModeForms Specify the discovery method used by PserverTCP/IP Commands Specify the NDS Tree where the Pserver object existsDefine NDS Tree Change TCP/IP RoutingEstablish or Change TCP/IP Nodes BootP, Dhcp and Rarp Parameters Show TCP/IP CharacteristicsDisplay the printer server’s TCP/IP characteristics Define BootP ParametersIf both n and m are zero, Dhcp is effectively disabled Define Dhcp ParametersDefine how many times printer server will attempt Dhcp Define Rarp ParametersLoad/Dump Configuration Define TCP/IP Load HostDefine Server Load Server define server preferred load ip ipaddressPower must by cycled after this command is performed Define Software File NameSet Load/Dump Gateway Server define server software filenameDefine TCP/IP Dump Host Server set define change server dump enabled disabledSet Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceShow Service Define ServiceDelete Service