Emulex Printer Server manual Server Commands, Define Server Name, Show Alarms

Page 27

Command Reference Guide 21

Server Commands

Define Server Name

Define the printer server’s node name.

>Server>> define server name prnsvr_nam

prnsvr_nam Enter a 1 to 16 character name for the printer server. This must be established with the Define command when any sessions are active. Any alphanumeric character is valid.

The printer server’s node name is used in certain commands and by host- initiated connections. The name must be different from all other node names on the same local network if the printer server accepts host- initiated connections or offers services.

Show Alarms

Show console error conditions.

>Server>> show server alarms

This command displays the number of nonfatal console errors that have occurred since the printer server was last booted, and the times and error numbers of the sixteen most recent errors.

Image 27

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide You will notice text boxes labeled Note or Caution What is a Command?Conventions FormattingVariables Command LinesPrompts KeywordsServer set define change server dhcp n m temp default OptionsQuotation Marks Set, Define And Change Keyword FunctionsClear, Purge And Delete Show, Monitor And ListChange node nodenam ip ipaddress tcpip gateway Command SummaryIpaddr set enabled disabled Enabled disabledTest portnum count countnum Help Initialize server delay delaymin cancelLogout port portnum Ping ipaddressCommand Reference Guide Halt Printer Server General CommandsEntire command crash 300 must be entered to be effective Display Internal ARP TableDelaymin InitializeBelow MIO Version Logout PasswordsUpdate Memory Sync Privileged AccessPassword Set Privilege PasswordChange Login Password Remote Console PasswordShow which nodes are known to the printer server Node CommandsShow Node Establish or Change TCP/IP NodesFacility GatewayNodename Define NetWare NodeDelete Node Remove nodes from the printer server’s internal node tableTest Port Port CommandsShow Port Characteristics Display the characteristics of a specified portSpecify the type of connections access the port can make Change Port AccessControl the line feed character Change Port TypeChange Line Feed Character Specify the type of terminal or printer connected to a portServer show monitor port portnum status netjet device Change Port SpeedShow Port Status NETJet BaudrateDefine Server Name Server CommandsShow Alarms Show console error conditionsShow Server Status Show Server CharacteristicsShow Server Configuration Display Network CharacteristicsDisplay the current configurable memory table allocation Show Server LimitsSet Console Terminal Port Enable or disable special printer server options Other OptionsAvailable options are Accright Set PromptModify Snmp Server set server prompt promptChange Domain Enable or Disable ProtocolsEnable or disable individual protocols ProtocolsAppleTalk Backspoofing Show NetBios CharacteristicsAppleTalk Show Server AppleTalkServer show list port portnum fonts Show FontsAdd Fonts Apple Remove Fonts AppleServer change port 1 fonts remove a Server show list server LAT Display the printer server’s LAT characteristicsChange Groups Show ServerDefine NetWare Node NetWare CommandsDefine Password Change Authorized GroupsServer show list server netware Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Choose Frame TypeServer define server netware required enabled disabled Define Required FileserverServer define node nodename nfserver Server set define change server netware rediscover minutes Adjust Processing SpeedDefine as Remote Printer Rediscover IntervalSpecify the discovery method used by Pserver Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode FormsChange TCP/IP Routing TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Define NDS TreeEstablish or Change TCP/IP Nodes Define BootP Parameters BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Display the printer server’s TCP/IP characteristicsDefine Rarp Parameters If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define how many times printer server will attempt DhcpServer define server preferred load ip ipaddress Load/Dump ConfigurationDefine TCP/IP Load Host Define Server LoadServer define server software filename Power must by cycled after this command is performedDefine Software File Name Set Load/Dump GatewayServer set define change server dump enabled disabled Set Dump HostDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Change Service Service CommandsDefine Service Delete ServiceShow Service