Emulex Printer Server manual Load/Dump Configuration, Define TCP/IP Load Host, Define Server Load

Page 46

40 Command Reference Guide

Load/Dump Configuration

Configuring a load host or dump host will allow you to:

•Upgrade printer server software.

•Define a workstation to receive and record memory image dumps.

Define TCP/IP Load Host

Specify the TCP/IP host where the printer server’s operational software will load from.

>Server>> define server preferred load ip ip_address

ip_address Enter the IP address of the node where the operational software is stored in decimal dot notation. For example, 123.234.345.490. The default is none.

Define Server Load

Specify the source of the operating software for subsequent loads. The command determines which load protocol the printer server uses the next time the printer server is reinitialized.

>Server>> define server load [selfload TFTP [put] decnet]

selfload	Upon reinitialization, the printer server self-loads
	its operational software from onboard non-
	volatile memory. This keyword requires special
	firmware which contains the operating software.
	A printer server configured for a selfload also
	has the ability to download its operational
	software from a network load host.
TFTP	Upon reinitialization, the printer server
	downloads its operational software from a
	network load host using standard TFTP load
	protocol.

Image 46

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide Formatting What is a Command?Conventions You will notice text boxes labeled Note or CautionKeywords Command LinesPrompts VariablesOptions Server set define change server dhcp n m temp defaultQuotation Marks Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledPing ipaddress Help Initialize server delay delaymin cancelLogout port portnum Test portnum count countnumCommand Reference Guide Display Internal ARP Table General CommandsEntire command crash 300 must be entered to be effective Halt Printer ServerInitialize DelayminBelow MIO Version Privileged Access PasswordsUpdate Memory Sync LogoutRemote Console Password Set Privilege PasswordChange Login Password PasswordEstablish or Change TCP/IP Nodes Node CommandsShow Node Show which nodes are known to the printer serverGateway FacilityRemove nodes from the printer server’s internal node table Define NetWare NodeDelete Node NodenameDisplay the characteristics of a specified port Port CommandsShow Port Characteristics Test PortChange Port Access Specify the type of connections access the port can makeSpecify the type of terminal or printer connected to a port Change Port TypeChange Line Feed Character Control the line feed characterBaudrate Change Port SpeedShow Port Status NETJet Server show monitor port portnum status netjet deviceShow console error conditions Server CommandsShow Alarms Define Server NameDisplay Network Characteristics Show Server CharacteristicsShow Server Configuration Show Server StatusShow Server Limits Display the current configurable memory table allocationSet Console Terminal Port Other Options Enable or disable special printer server optionsAvailable options are Server set server prompt prompt Set PromptModify Snmp AccrightProtocols Enable or Disable ProtocolsEnable or disable individual protocols Change DomainShow Server AppleTalk Show NetBios CharacteristicsAppleTalk AppleTalk BackspoofingRemove Fonts Apple Show FontsAdd Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Show Server Display the printer server’s LAT characteristicsChange Groups Server show list server LATChange Authorized Groups NetWare CommandsDefine Password Define NetWare NodeChoose Frame Type Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Server show list server netwareDefine Required Fileserver Server define server netware required enabled disabledServer define node nodename nfserver Rediscover Interval Adjust Processing SpeedDefine as Remote Printer Server set define change server netware rediscover minutesForms Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode Specify the discovery method used by PserverDefine NDS Tree TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Change TCP/IP RoutingEstablish or Change TCP/IP Nodes Display the printer server’s TCP/IP characteristics BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Define BootP ParametersDefine how many times printer server will attempt Dhcp If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define Rarp ParametersDefine Server Load Load/Dump ConfigurationDefine TCP/IP Load Host Server define server preferred load ip ipaddressSet Load/Dump Gateway Power must by cycled after this command is performedDefine Software File Name Server define server software filenameSet Dump Host Server set define change server dump enabled disabledDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceDelete Service Define ServiceShow Service