Emulex Printer Server manual Conventions, What is a Command?, Formatting

Page 7

Command Reference Guide 1

Conventions

This guide provides the correct syntax for commands used with Emulex printer servers containing software release 5.0. This section describes both general and command conventions used in this document and in other printer server documentation.

NOTE: The user must login to the printer server to perform an Emulex printer server command.

Formatting

You will notice text boxes labeled NOTE or CAUTION.

•Notes provide additional information.

•Caution statements provide warnings to prevent harm to people or equipment.

CAUTION: Observe electrostatic discharge (ESD) procedures during installation.

What is a Command?

A prompt, followed by a keyword and one or more variables, options or quotation marks make up a command. The following explanation will demonstrate the structure and formatting of 5.0 printer server commands.

Image 7

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide You will notice text boxes labeled Note or Caution What is a Command?Conventions FormattingVariables Command LinesPrompts KeywordsOptions Server set define change server dhcp n m temp defaultQuotation Marks Set, Define And Change Keyword FunctionsClear, Purge And Delete Show, Monitor And ListChange node nodenam ip ipaddress tcpip gateway Command SummaryIpaddr set enabled disabled Enabled disabledTest portnum count countnum Help Initialize server delay delaymin cancelLogout port portnum Ping ipaddressCommand Reference Guide Halt Printer Server General CommandsEntire command crash 300 must be entered to be effective Display Internal ARP TableInitialize DelayminBelow MIO Version Logout PasswordsUpdate Memory Sync Privileged AccessPassword Set Privilege PasswordChange Login Password Remote Console PasswordShow which nodes are known to the printer server Node CommandsShow Node Establish or Change TCP/IP NodesFacility GatewayNodename Define NetWare NodeDelete Node Remove nodes from the printer server’s internal node tableTest Port Port CommandsShow Port Characteristics Display the characteristics of a specified portSpecify the type of connections access the port can make Change Port AccessControl the line feed character Change Port TypeChange Line Feed Character Specify the type of terminal or printer connected to a portServer show monitor port portnum status netjet device Change Port SpeedShow Port Status NETJet BaudrateDefine Server Name Server CommandsShow Alarms Show console error conditionsShow Server Status Show Server CharacteristicsShow Server Configuration Display Network CharacteristicsShow Server Limits Display the current configurable memory table allocationSet Console Terminal Port Other Options Enable or disable special printer server optionsAvailable options are Accright Set PromptModify Snmp Server set server prompt promptChange Domain Enable or Disable ProtocolsEnable or disable individual protocols ProtocolsAppleTalk Backspoofing Show NetBios CharacteristicsAppleTalk Show Server AppleTalkServer show list port portnum fonts Show FontsAdd Fonts Apple Remove Fonts AppleServer change port 1 fonts remove a Server show list server LAT Display the printer server’s LAT characteristicsChange Groups Show ServerDefine NetWare Node NetWare CommandsDefine Password Change Authorized GroupsServer show list server netware Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Choose Frame TypeDefine Required Fileserver Server define server netware required enabled disabledServer define node nodename nfserver Server set define change server netware rediscover minutes Adjust Processing SpeedDefine as Remote Printer Rediscover IntervalSpecify the discovery method used by Pserver Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode FormsChange TCP/IP Routing TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Define NDS TreeEstablish or Change TCP/IP Nodes Define BootP Parameters BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Display the printer server’s TCP/IP characteristicsDefine Rarp Parameters If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define how many times printer server will attempt DhcpServer define server preferred load ip ipaddress Load/Dump ConfigurationDefine TCP/IP Load Host Define Server LoadServer define server software filename Power must by cycled after this command is performedDefine Software File Name Set Load/Dump GatewaySet Dump Host Server set define change server dump enabled disabledDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Change Service Service CommandsDelete Service Define ServiceShow Service