Emulex Printer Server manual Set Dump Host, Define TCP/IP Dump Host

Page 48

42 Command Reference Guide

	IP address for both the load and dump
	functions.
ip_address	Enter the IP address of the gateway node in
	decimal dot notation. For example,
	123.234.345.490. This address must be on the
	same subnet as the printer server.
none	Enter none to remove an existing IP address.
	Although no IP address is chosen, the printer
	server attempts the load or dump operation
	without using a gateway. The printer server
	attempts to use the IP address of the load or
	dump host even if the host IP address is on a
	different subnet than the printer server’s IP
	address.

When the printer server loads its internal software over the network, it checks to see if a gateway load_dump IP address has been set and uses the set gateway to contact the node from which it will download its operational software. In the same way, when the printer server performs a crash dump upload, it checks to see if a gateway load_dump IP address has been set and uses the set gateway to contact the node to which it will send the dump of its internal memory.

Set Dump Host

Enable or disable the printer server’s ability to send a copy of its internal memory to a specified dump host.

>Server>> [set define change] server dump [enabled disabled]

enabled	Default is enabled. When this command is
	enabled, the printer server sends a file memory
	image to a specified host before reinitializing
	after a fatal error or upon execution of a Crash
	300 command.
disabled	When the command is disabled, no dump can
	occur. Prior to a dump occurring, a preferred
	dump node must be specified.

Define TCP/IP Dump Host

Image 48

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide What is a Command? ConventionsFormatting You will notice text boxes labeled Note or CautionCommand Lines PromptsKeywords VariablesServer set define change server dhcp n m temp default OptionsQuotation Marks Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledHelp Initialize server delay delaymin cancel Logout port portnumPing ipaddress Test portnum count countnumCommand Reference Guide General Commands Entire command crash 300 must be entered to be effectiveDisplay Internal ARP Table Halt Printer ServerDelaymin InitializeBelow MIO Version Passwords Update Memory SyncPrivileged Access LogoutSet Privilege Password Change Login PasswordRemote Console Password PasswordNode Commands Show NodeEstablish or Change TCP/IP Nodes Show which nodes are known to the printer serverGateway FacilityDefine NetWare Node Delete NodeRemove nodes from the printer server’s internal node table NodenamePort Commands Show Port CharacteristicsDisplay the characteristics of a specified port Test PortChange Port Access Specify the type of connections access the port can makeChange Port Type Change Line Feed CharacterSpecify the type of terminal or printer connected to a port Control the line feed characterChange Port Speed Show Port Status NETJetBaudrate Server show monitor port portnum status netjet deviceServer Commands Show AlarmsShow console error conditions Define Server NameShow Server Characteristics Show Server ConfigurationDisplay Network Characteristics Show Server StatusDisplay the current configurable memory table allocation Show Server LimitsSet Console Terminal Port Enable or disable special printer server options Other OptionsAvailable options are Set Prompt Modify SnmpServer set server prompt prompt AccrightEnable or Disable Protocols Enable or disable individual protocolsProtocols Change DomainShow NetBios Characteristics AppleTalkShow Server AppleTalk AppleTalk BackspoofingShow Fonts Add Fonts AppleRemove Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Display the printer server’s LAT characteristics Change GroupsShow Server Server show list server LATNetWare Commands Define PasswordChange Authorized Groups Define NetWare NodeDisplay Characteristics Display the printer server’s Novell NetWare characteristicsChoose Frame Type Server show list server netwareServer define server netware required enabled disabled Define Required FileserverServer define node nodename nfserver Adjust Processing Speed Define as Remote PrinterRediscover Interval Server set define change server netware rediscover minutesEnable or disable the NetWare forms function Selecting Bindery Emulation or NDS ModeForms Specify the discovery method used by PserverTCP/IP Commands Specify the NDS Tree where the Pserver object existsDefine NDS Tree Change TCP/IP RoutingEstablish or Change TCP/IP Nodes BootP, Dhcp and Rarp Parameters Show TCP/IP CharacteristicsDisplay the printer server’s TCP/IP characteristics Define BootP ParametersIf both n and m are zero, Dhcp is effectively disabled Define Dhcp ParametersDefine how many times printer server will attempt Dhcp Define Rarp ParametersLoad/Dump Configuration Define TCP/IP Load HostDefine Server Load Server define server preferred load ip ipaddressPower must by cycled after this command is performed Define Software File NameSet Load/Dump Gateway Server define server software filenameServer set define change server dump enabled disabled Set Dump HostDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceDefine Service Delete ServiceShow Service