Emulex Printer Server manual Change Port Speed, Show Port Status NETJet, Baudrate

Page 26

20 Command Reference Guide

Change Port Speed

Set the serial communication speed (baud rate) in bits per second.

>Server>> [set define change] port port_num [input output] speed baud_rate

port_num

The port affected by speed change.

input

Enter the speed at which data is received. If

 

input speed is not chosen, the command sets

 

the speed in both directions.

output

Enter the speed at which data is transmitted. If

 

output speed is not chosen, the command sets

 

the speed in both directions.

baud_rate

Enter a speed: 75, 110, 134, 150, 300, 600,

 

1200, 2400, 1800, 2000, 2400, 4800, 9600,

 

19200, 38400.

Show Port Status - NETJet

Display port status for NETJet printer servers and MIO interfaces.

>Server>> [show monitor] port port_num status [netjet device]

port_num

Enter the port number for which status is

 

desired.

netjet

Gives the status for NETJet connected to MIO

 

interface (port 1).

device

Gives the status of a Hewlett-Packard MIO

 

printer interface.

Image 26
Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide Formatting What is a Command?Conventions You will notice text boxes labeled Note or CautionKeywords Command LinesPrompts VariablesQuotation Marks Server set define change server dhcp n m temp defaultOptions Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledPing ipaddress Help Initialize server delay delaymin cancelLogout port portnum Test portnum count countnumCommand Reference Guide Display Internal ARP Table General CommandsEntire command crash 300 must be entered to be effective Halt Printer ServerBelow MIO Version DelayminInitialize Privileged Access PasswordsUpdate Memory Sync LogoutRemote Console Password Set Privilege PasswordChange Login Password PasswordEstablish or Change TCP/IP Nodes Node CommandsShow Node Show which nodes are known to the printer serverGateway FacilityRemove nodes from the printer server’s internal node table Define NetWare NodeDelete Node NodenameDisplay the characteristics of a specified port Port CommandsShow Port Characteristics Test PortChange Port Access Specify the type of connections access the port can makeSpecify the type of terminal or printer connected to a port Change Port TypeChange Line Feed Character Control the line feed characterBaudrate Change Port SpeedShow Port Status NETJet Server show monitor port portnum status netjet deviceShow console error conditions Server CommandsShow Alarms Define Server NameDisplay Network Characteristics Show Server CharacteristicsShow Server Configuration Show Server StatusSet Console Terminal Port Display the current configurable memory table allocationShow Server Limits Available options are Enable or disable special printer server optionsOther Options Server set server prompt prompt Set PromptModify Snmp AccrightProtocols Enable or Disable ProtocolsEnable or disable individual protocols Change DomainShow Server AppleTalk Show NetBios CharacteristicsAppleTalk AppleTalk BackspoofingRemove Fonts Apple Show FontsAdd Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Show Server Display the printer server’s LAT characteristicsChange Groups Server show list server LATChange Authorized Groups NetWare CommandsDefine Password Define NetWare NodeChoose Frame Type Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Server show list server netwareServer define node nodename nfserver Server define server netware required enabled disabledDefine Required Fileserver Rediscover Interval Adjust Processing SpeedDefine as Remote Printer Server set define change server netware rediscover minutesForms Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode Specify the discovery method used by PserverDefine NDS Tree TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Change TCP/IP RoutingEstablish or Change TCP/IP Nodes Display the printer server’s TCP/IP characteristics BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Define BootP ParametersDefine how many times printer server will attempt Dhcp If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define Rarp ParametersDefine Server Load Load/Dump ConfigurationDefine TCP/IP Load Host Server define server preferred load ip ipaddressSet Load/Dump Gateway Power must by cycled after this command is performedDefine Software File Name Server define server software filenameDefine TCP/IP Dump Host Server set define change server dump enabled disabledSet Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceShow Service Define ServiceDelete Service