Emulex Printer Server manual Define Software File Name, Set Load/Dump Gateway

Page 47

 

Command Reference Guide 41

put

Use this keyword when the environment does

 

not support BootP, DHCP, or TFTP server load

 

requests to a printer server.

decnet

Upon reinitialization, the printer server

 

downloads its operational software from a

 

network load host using standard decnet-

 

compatible load protocol. The default is dec.

Power must by cycled after this command is performed.

Define Software File Name

Specify the file name of the file on a load host that contains the printer server’s operational software.

>Server>> define server software file_name

file_name Enter the name of the file that contains the printer server’s operational software. For DECnet load hosts, this is a 1 to 9 character file name. For TFTP load hosts, this is a 1 to 16 character file name. See the chart below for DECnet and TFTP file names:

Printer Server

TFTP

DECnet

NETJet

NJATLNE

NJATLNE.SYS

NETQue

NQATLNE

NQATLNE.SYS

Token Ring

NQTTLNE

NQTTLNE.SYE

NETQue Mate

NQMTLNE

NQMTLNE.SYS

NETQue Pro2

NP2TLNE

NP2TLNE.SYS

Set Load/Dump Gateway

Specify the IP address of the gateway through which the printer server loads and dumps its internal software.

>Server>> define server gateway [load_dump] ip [ip_address none]

load_dump Enter the gateway through which the printer server loads and dumps its internal software. The printer server maintains only one gateway

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide You will notice text boxes labeled Note or Caution What is a Command?Conventions FormattingVariables Command LinesPrompts KeywordsQuotation Marks Server set define change server dhcp n m temp defaultOptions Set, Define And Change Keyword FunctionsClear, Purge And Delete Show, Monitor And ListChange node nodenam ip ipaddress tcpip gateway Command SummaryIpaddr set enabled disabled Enabled disabledTest portnum count countnum Help Initialize server delay delaymin cancelLogout port portnum Ping ipaddressCommand Reference Guide Halt Printer Server General CommandsEntire command crash 300 must be entered to be effective Display Internal ARP TableBelow MIO Version DelayminInitialize Logout PasswordsUpdate Memory Sync Privileged AccessPassword Set Privilege PasswordChange Login Password Remote Console PasswordShow which nodes are known to the printer server Node CommandsShow Node Establish or Change TCP/IP NodesFacility GatewayNodename Define NetWare NodeDelete Node Remove nodes from the printer server’s internal node tableTest Port Port CommandsShow Port Characteristics Display the characteristics of a specified portSpecify the type of connections access the port can make Change Port AccessControl the line feed character Change Port TypeChange Line Feed Character Specify the type of terminal or printer connected to a portServer show monitor port portnum status netjet device Change Port SpeedShow Port Status NETJet BaudrateDefine Server Name Server CommandsShow Alarms Show console error conditionsShow Server Status Show Server CharacteristicsShow Server Configuration Display Network CharacteristicsSet Console Terminal Port Display the current configurable memory table allocationShow Server Limits Available options are Enable or disable special printer server optionsOther Options Accright Set PromptModify Snmp Server set server prompt promptChange Domain Enable or Disable ProtocolsEnable or disable individual protocols ProtocolsAppleTalk Backspoofing Show NetBios CharacteristicsAppleTalk Show Server AppleTalkServer show list port portnum fonts Show FontsAdd Fonts Apple Remove Fonts AppleServer change port 1 fonts remove a Server show list server LAT Display the printer server’s LAT characteristicsChange Groups Show ServerDefine NetWare Node NetWare CommandsDefine Password Change Authorized GroupsServer show list server netware Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Choose Frame TypeServer define node nodename nfserver Server define server netware required enabled disabledDefine Required Fileserver Server set define change server netware rediscover minutes Adjust Processing SpeedDefine as Remote Printer Rediscover IntervalSpecify the discovery method used by Pserver Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode FormsChange TCP/IP Routing TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Define NDS TreeEstablish or Change TCP/IP Nodes Define BootP Parameters BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Display the printer server’s TCP/IP characteristicsDefine Rarp Parameters If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define how many times printer server will attempt DhcpServer define server preferred load ip ipaddress Load/Dump ConfigurationDefine TCP/IP Load Host Define Server LoadServer define server software filename Power must by cycled after this command is performedDefine Software File Name Set Load/Dump GatewayDefine TCP/IP Dump Host Server set define change server dump enabled disabledSet Dump Host Server define server preferred dump ip ipaddress Change Service Service CommandsShow Service Define ServiceDelete Service
Top Page Image Contents