Cabletron Systems manual Chapter Setup and Installation, Installing the WPIM-RT1

Page 17

CHAPTER 2

SETUP AND INSTALLATION

Only qualiﬁed personnel should install the WPIM-RT1. This User’s Guide is intended for the experienced network equipment installer.

The following information in this chapter details the set up and installation of the WPIM-RT1 into a host platform.

NOTE

QuickSET or Local Management must be used to set up the WPIM-RT1 in management before any connections are made to the WAN. Follow the directions in this chapter carefully in order to connect the WAN cable at the proper time.

2.1INSTALLING THE WPIM-RT1

WPIM-RT1

27502

Figure 2-1 WPIM-RT1

For additional support related to the WPIM-RT1, refer to the host platform manual into which the WPIM-RT1 is being installed. Locate the guide by clicking on the Cabletron Systems QuickSET program group icon after installing the QuickSET CD on your computer, or see Related Manuals in the Introduction.

NOTE

Some WPIMs require version 1.02 or greater of QuickSET to participate and function correctly in your network. Contact Cabletron Systems to obtain the latest version of QuickSET.

The information in this note does not apply if the WPIM-RT1 is being installed into the HSIM-SSA710. Please refer to the documentation for the HSIM-SSA710 if the WPIM-RT1 is being installed in an HSIM-SSA710.

WPIM-RT1 User’s Guide

2-1

Image 17

Contents WPIM-RT1 Page WPIM-RT1 User’s Guide FCC NoticeVcci Notice Industry Canada NoticeCabletron Software Program License Exclusion of Warranty and Disclaimer of LiabilityCabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights PO Box Rochester, NH Declaration of ConformityWPIM-RT1 User’s Guide Contents Viii WPIM-RT1 User’s Guide Structure of this Guide Using this ManualIntroduction Related Manuals Following conventions are used throughout this document Document ConventionsYour email address Getting HelpChapter Overview WAN Protocols WPIM-RT1 FeaturesIsdn MIB SupportInstalling the WPIM-RT1 Chapter Setup and InstallationUnpacking the WPIM-RT1 Pre-InstallationInstalling the WPIM-RT1 Installing the WPIM-RT1 Post-InstallationRequired Management Operations Connecting the WAN Cable to the WPIM-RT1Host Platform LEDs Connecting the WAN cable to the WPIM-RT1 WPIM-RT1 User’s Guide Chapter Local Management WAN Physical Conﬁguration Screen Fields WAN Physical Configuration ScreenDisplays the next interface available to be used Wpim Line Conﬁguration Fields Sample Timeslot Conﬁguration Wpim Timeslot Conﬁguration TableSample Conﬁguration WAN Interface Conﬁguration Screen Fields WAN Interface Configuration ScreenFrame Relay as the Protocol Manager WAN Interface Conﬁguration Screen PPP PPP as the Protocol ManagerCommand Fields and Interface Table Fields Configuration Information Required by User Full T1 Configuration Using PPP1 T1 Physical Conﬁguration 2 T1 Interface Conﬁguration Fractional T1 Conﬁguration Fractional T1 Configuration Using PPPFractional T1 Conﬁguration Using PPP Enter Frame Relay Conﬁguration Frame Relay ConfigurationFrame Relay Physical Conﬁguration Frame Relay Conﬁguration Frame Relay Interface Conﬁguration Frame Relay Conﬁguration WPIM-RT1 User’s Guide Physical Properties Appendix a SpecificationsEnvironmental Requirements Regulatory ComplianceCable Assemblies and Pinouts T1 Interface CablingREN/SOC FIC Usoc Appendix B FCC Part 68 USER’S InformationAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires