Cabletron Systems WPIM-RT1 manual 1 T1 Physical Configuration

Page 34

Chapter 3: Local Management

3.3.1T1 Physical Configuration

Begin the T1 configuration by accessing the WAN Physical Configuration screen through Local Management (Figure 3-1). Access the WAN Physical Configuration screen from the WAN SETUP menu item in the host platform.

Proceed with the following steps:

1.Use the arrow keys to highlight the [WPIM X] field at the bottom of the screen. Press the SPACE bar to select the number of the WPIM to be configured, then press ENTER.

2.Use the arrow keys to highlight MgrType. Select PPP.

NOTE

When changing from one protocol to another on a WPIM-RT1 that has been operational, save NONE as the protocol before changing to another protocol.

3.Use the arrow keys to highlight Timeslot View. Press the SPACE bar to select New, then press ENTER. The cursor moves to Timeslot #1 of the Timeslot Configuration Table.

4.Insert an interface number into every timeslot as needed (refer to the note below). Type the number, press ENTER, then use the arrow keys to highlight the next timeslot field. Exit this field by using the arrow keys. The cursor automatically moves to the T1 Line Coding field.

NOTE

The value assigned to the timeslots is the interface being used for WAN communication. The next available interface is displayed on the WAN Physical Configuration screen in the Next IF field (seeFigure 3-1). The Next IF number shown must be used to add a new interface. The Next IF will increment as interfaces are added. The previously entered interfaces can be modified by entering the interface number.

The following four steps are based on information supplied by the service provider. Consult the service provider for the correct settings.

5.Use the arrow keys to highlight T1 Line Coding. Press the SPACE bar to select B8ZS or AMI, then press ENTER.

6.Use the arrow keys to highlight T1 Frame Type. Press the SPACE bar to select ESF or D4, then press ENTER.

3-12

WPIM-RT1 User’s Guide

Image 34
Contents WPIM-RT1 Page FCC Notice WPIM-RT1 User’s GuideIndustry Canada Notice Vcci NoticeCabletron SYSTEMS, INC. Program License Agreement Exclusion of Warranty and Disclaimer of LiabilityCabletron Software Program License United States Government Restricted Rights Declaration of Conformity PO Box Rochester, NHWPIM-RT1 User’s Guide Contents Viii WPIM-RT1 User’s Guide Introduction Using this ManualStructure of this Guide Related Manuals Document Conventions Following conventions are used throughout this documentGetting Help Your email addressChapter Overview Isdn WPIM-RT1 FeaturesWAN Protocols MIB SupportChapter Setup and Installation Installing the WPIM-RT1Installing the WPIM-RT1 Pre-InstallationUnpacking the WPIM-RT1 Post-Installation Installing the WPIM-RT1Host Platform LEDs Connecting the WAN Cable to the WPIM-RT1Required Management Operations Connecting the WAN cable to the WPIM-RT1 WPIM-RT1 User’s Guide Chapter Local Management WAN Physical Configuration Screen WAN Physical Configuration Screen FieldsDisplays the next interface available to be used Wpim Line Configuration Fields Wpim Timeslot Configuration Table Sample Timeslot ConfigurationSample Configuration WAN Interface Configuration Screen WAN Interface Configuration Screen FieldsFrame Relay as the Protocol Manager PPP as the Protocol Manager WAN Interface Configuration Screen PPPCommand Fields and Interface Table Fields Full T1 Configuration Using PPP Configuration Information Required by User1 T1 Physical Configuration 2 T1 Interface Configuration Fractional T1 Configuration Using PPP Fractional T1 ConfigurationFractional T1 Configuration Using PPP Enter Frame Relay Configuration Frame Relay ConfigurationFrame Relay Physical Configuration Frame Relay Configuration Frame Relay Interface Configuration Frame Relay Configuration WPIM-RT1 User’s Guide Environmental Requirements Appendix a SpecificationsPhysical Properties Regulatory ComplianceT1 Interface Cabling Cable Assemblies and PinoutsAppendix B FCC Part 68 USER’S Information REN/SOC FIC UsocAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires