Cabletron Systems WPIM-RT1 Appendix a Specifications, Physical Properties, Regulatory Compliance

Page 45

APPENDIX A

SPECIFICATIONS

This appendix provides operating speciﬁcations and cabling information for the Cabletron Systems WPIM-RT1. Cabletron Systems reserves the right to change these speciﬁcations at any time without notice.

A.1 PHYSICAL PROPERTIES

	Dimensions	1.94 H x 6.2 W x 15.06	D (cm)
	Dimensions	.762 H x 2.44 W x 5.93	D (in)
		.762 H x 2.44 W x 5.93	D (in)

	Weight	113.6 g (4 ounces)

	MTBF (Predicted)	200,000 hours

A.2 ENVIRONMENTAL REQUIREMENTS

Operating Temperature	5°C to 40°C (41°F to 104°F)

Storage Temperature	-30°C to 73°C (-22°F to 164°F)

Relative Humidity	5% to 90% (non-condensing)

A.3 REGULATORY COMPLIANCE

This equipment meets the following safety and electromagnetic compatibility (EMC) requirements:

	Safety	UL 1950, CSA C22.2 No. 950,
	Safety	EN 60950, IEC 950 73/23/EEC
		EN 60950, IEC 950 73/23/EEC

	Electromagnetic Compatibility	FCC Part 15, EN 55022, VCCI V-3,
	Electromagnetic Compatibility	CSA/08.8, EN 50082-1,
	(EMC)	CSA/08.8, EN 50082-1,
	(EMC)	AS/NZS 354, 89/336/EEC
		AS/NZS 354, 89/336/EEC

	Telecommunications	FCC CFR47 Part 68, CS-03

WPIM-RT1 User’s Guide

A-1

Image 45

Contents WPIM-RT1 Page WPIM-RT1 User’s Guide FCC NoticeVcci Notice Industry Canada NoticeExclusion of Warranty and Disclaimer of Liability Cabletron SYSTEMS, INC. Program License AgreementCabletron Software Program License United States Government Restricted Rights PO Box Rochester, NH Declaration of ConformityWPIM-RT1 User’s Guide Contents Viii WPIM-RT1 User’s Guide Using this Manual IntroductionStructure of this Guide Related Manuals Following conventions are used throughout this document Document ConventionsYour email address Getting HelpChapter Overview WAN Protocols WPIM-RT1 FeaturesIsdn MIB SupportInstalling the WPIM-RT1 Chapter Setup and InstallationPre-Installation Installing the WPIM-RT1Unpacking the WPIM-RT1 Installing the WPIM-RT1 Post-InstallationConnecting the WAN Cable to the WPIM-RT1 Host Platform LEDsRequired Management Operations Connecting the WAN cable to the WPIM-RT1 WPIM-RT1 User’s Guide Chapter Local Management WAN Physical Conﬁguration Screen Fields WAN Physical Configuration ScreenDisplays the next interface available to be used Wpim Line Conﬁguration Fields Sample Timeslot Conﬁguration Wpim Timeslot Conﬁguration TableSample Conﬁguration WAN Interface Conﬁguration Screen Fields WAN Interface Configuration ScreenFrame Relay as the Protocol Manager WAN Interface Conﬁguration Screen PPP PPP as the Protocol ManagerCommand Fields and Interface Table Fields Configuration Information Required by User Full T1 Configuration Using PPP1 T1 Physical Conﬁguration 2 T1 Interface Conﬁguration Fractional T1 Conﬁguration Fractional T1 Configuration Using PPPFractional T1 Conﬁguration Using PPP Enter Frame Relay Conﬁguration Frame Relay ConfigurationFrame Relay Physical Conﬁguration Frame Relay Conﬁguration Frame Relay Interface Conﬁguration Frame Relay Conﬁguration WPIM-RT1 User’s Guide Physical Properties Appendix a SpecificationsEnvironmental Requirements Regulatory ComplianceCable Assemblies and Pinouts T1 Interface CablingREN/SOC FIC Usoc Appendix B FCC Part 68 USER’S InformationAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires