Cabletron Systems TRXI-44, TRXI-22, TRXI-42 Static System Messages, Displayed Message Comments

Page 51

TESTING AND TROUBLESHOOTING

4.3.1Static System Messages

These messages display TRXI configuration information. To view the Static System Messages, momentarily press the Display button located below the LCD window. Press the Display button to scroll through each message. If you do not press the Display button within ten seconds, the display defaults back to the product name.

Displayed Message

Comments

IP Address

Displays the current IP

xxx.xxx.xxx.xxx

address. This may be changed

 

through Local Management.

MAC Address

Displays the Hardware

0000B8xxxxxx

or MAC address.

RAM Image

Displays the revision number of the

Rev. xx.xx.xx

Flash EEPROM.

Boot PROM

Displays the revision number of the

Rev. xx.xx.xx

internal Boot PROM.

Flash Programmed

Displays the number of times the

xx Times

the Flash EEPROM has been

 

programmed

COM 1

Displays the current baud rate

Baud Rate xxxxxx

of the COM 1 port.

COM 1

Displays the current function

Function xxxxxx

(Console, Modem, UPS, or SLIP) of

 

the COM 1 port.

COM 2

Displays the current

Baud Rate xxxxxx

baud rate of the COM 2 port.

COM 2

Display the current function

Function xxxxxx

(-N/A-, Console, Modem, UPS, or

 

SLIP) of the COM 2 port.

Page 4-4

Image 51
Contents Token Ring Intelligent HUB USER’S Guide Printed On Recycled Paper FCC Notice Exclusion of Warranty and Disclaimer of Liability Contents Table of Contents Introduction REQUIREMENTS/SPECIFICATIONSInstallation Contents Testing and TroubleshootingLocal Management Chapter Introduction Using this ManualTrxi Overview Introduction Getting HelpTrxi Features Token Ring Port Interface Modules TPIMs Media Type ConnectorRmon MIB Support Group Subgroup SectionRecommended Reading Flash EEPROMsCabletron’s Distributed LAN Monitor Remote Network Management CapabilitiesCable Specifications Chapter REQUIREMENTS/SPECIFICATIONSFrequency Impedance Attenuation Attenuation and ImpedanceMaximum Number of Stations Maximum Lobe LengthsUTP Cable Type Maximum Lobe Length Mbps Type 3 Media FiltersREQUIREMENTS/SPECIFICATIONS Maximum Trunk Lengths STP Cable Type Ring Speed MbpsMixed Cable Types Multimode Fiber Optic Cable Specifications for the TPIM-F2 Cable Type Attenuation Maximum Drive DistanceFiber Optic Budget Single Mode Fiber Optic Cable Specifications for the TPIM-F3 Temperature CrosstalkNoise REQUIREMENTS/SPECIFICATIONS UPS REQUIREMENTS/SPECIFICATIONS COM 1/COM 2 Port SpecificationsConsole ModemTPIM-T1 REQUIREMENTS/SPECIFICATIONS Tpim SpecificationsTPIM-T4 REQUIREMENTS/SPECIFICATIONS TPIM-T2REQUIREMENTS/SPECIFICATIONS TPIM-F2 Parameter Typical Worst Worst Case TypicalValue Case Budget TPIM-F3 REQUIREMENTS/SPECIFICATIONS TPIM-F3Parameter Typical Minimum Maximum Environmental Requirements REQUIREMENTS/SPECIFICATIONS General SpecificationsPower Supply Requirements Output Min. Load Max. Load Max PowerREQUIREMENTS/SPECIFICATIONS Safety ServicePhysical Attaching the Strain Relief Bracket Unpacking the TrxiAttaching the Strain Relief Installing the TrxiRack Mounting the Trxi Installing the Trxi in the RackWall Mounting the Trxi Free-Standing Installation Ring Speed Switch Settings Installation Setting the Ring Speed SwitchInstallation Setting the Nvram Switch Connecting the Network Lobe Port Cabling Installation Connecting the Trxi to the Power SourceConfiguration Examples for TRXI-24 and TRXI-44 LNK TPIM-T4 Installation Installing the Tpim RI/RO Modules Top View Setting the TPIM’s Phantom Switch and RI/RO Switch12. Installing a Tpim Installing a Tpim to the TrxiConnecting a Twisted Pair Segment to the TPIM-T1 Connecting a Twisted Pair Segment to the TPIM-T2 or TPIM-T4 Installation LNK Finishing the Installation Checking the Installation Chapter Testing and TroubleshootingTRXI-24TOKEN Ring HUB with Lanview Testing and Troubleshooting Using LanviewLCD Testing and Troubleshooting LCD DisplayDisplayed Message Comments Static System MessagesDisplayed Messages Comments Alarm MessagesFailure or Error Messages Unsaved Initialization MessagesNormal Unsaved Initialization Messages Displayed Message Saved System MessagesChapter Local Management Attaching the Management Terminal Local Management Management Terminal RequirementsSetup Setting the Management Terminal Setup ParametersDisplay Setup General SetupRJ45 COM 2 Port Modem Cable Configuration and SetupTrxi Local Management Local Management Accessing Local ManagementMain Menu Local Management Using Local ManagementSelecting a Menu Option Exiting a Local Management ScreenExiting Your Local Management Session IP Address System Level ScreenSystem Date System TimeClear All Nvram Setting the System DateCOM 1 Application COM 2 ApplicationSetting the IP Address Setting the System TimeSetting the Subnet Mask Setting the Enable Beacon Recovery Field Setting the Clear All Nvram FieldSnmp Community Names Screen Editing the Community Name Field AccessComponent Name Community NameTrap Community Name Enable TrapsSnmp Traps Screen Trap DestinationSetting Snmp Traps Ring Security Screen Security Mode Station AddressStn Edit Return SAVE/EXECUTENextscreen PreviousscreenAdding Stations to the Station Address Allowed List Building the Allowed ListDeleting Stations from the Station Address Allowed List Changing the Ring Security ModeDevice Statistics Screen Device StatisticsInterface Isolating Errors Ring Information Ring Number Ports EnabledNON-ISOLATING Errors Lost Frame ErrorsFrequency Errors Frame Copied ErrorsRcvr Congestion Errors Token ErrorsSetting the Refresh Field Selecting the Device Statistics Counter ModeTemp Enable All PortsChassis Status View Screen Port StatusReturn Setting the Enable All Ports OptionSetting the Operational/Administrative Mode Option Operational11. Component Status View Screen Component Status View ScreenSnmp Tools Screen Walk GETSET GetnextSecurity Access Level Getting and Setting OIDsCommunity Name Local Management Scrolling Through MIB OIDs Local Management Local Management French Power Supply CordGerman Spanish