Cabletron Systems TRXI-22, TRXI-42, TRXI-24 Local Management Using Local Management, Main Menu

Page 60

LOCAL MANAGEMENT

5.3USING LOCAL MANAGEMENT

TRXI Local Management consists of three menu screens:

the Main Menu screen

the Device Setup screen

and the Device Status screen.

Menu screens list TRXI Local Management options. Figure 5-4 shows the menu screens and each Local Management option. The following sections explain how to select and use each of the Local Management options.

TRXI LOCAL MANAGEMENT

Flash Image Version: X.XX.XX

MAIN MENU

DEVICE SETUP

DEVICE STATUS

DEVICE STATISTICS

MIB NAVIGATOR

SNMP TOOL

EXIT LM

TRXI LOCAL MANAGEMENT

Flash Image Version: X.XX.XX

DEVICE STATUS

CHASSIS STATUS VIEW

COMPONENT STATUS VIEW

RMON VIEW

TRXI LOCAL MANAGEMENT

Flash Image Version: X.XX.XX

DEVICE SETUP

SYSTEM LEVEL

SNMP COMMUNITY NAMES

SNMP TRAPS

RING SECURITY

FLASH DOWNLOAD

RETURN

RETURN

Figure 5-4. Local Management Menu Screen

Page 5-6

Image 60
Contents Token Ring Intelligent HUB USER’S Guide Printed On Recycled Paper FCC Notice Exclusion of Warranty and Disclaimer of Liability Contents Table of Contents Introduction REQUIREMENTS/SPECIFICATIONSInstallation Contents Testing and TroubleshootingLocal Management Using this Manual Chapter IntroductionIntroduction Getting Help Trxi OverviewTrxi Features Media Type Connector Rmon MIB SupportGroup Subgroup Section Token Ring Port Interface Modules TPIMsFlash EEPROMs Cabletron’s Distributed LAN MonitorRemote Network Management Capabilities Recommended ReadingChapter REQUIREMENTS/SPECIFICATIONS Cable SpecificationsAttenuation and Impedance Frequency Impedance AttenuationMaximum Lobe Lengths UTP Cable Type Maximum Lobe Length MbpsType 3 Media Filters Maximum Number of StationsREQUIREMENTS/SPECIFICATIONS STP Cable Type Ring Speed Mbps Maximum Trunk LengthsMixed Cable Types Multimode Fiber Optic Cable Specifications for the TPIM-F2 Cable Type Attenuation Maximum Drive DistanceFiber Optic Budget Single Mode Fiber Optic Cable Specifications for the TPIM-F3 Temperature CrosstalkNoise REQUIREMENTS/SPECIFICATIONS REQUIREMENTS/SPECIFICATIONS COM 1/COM 2 Port Specifications ConsoleModem UPSREQUIREMENTS/SPECIFICATIONS Tpim Specifications TPIM-T1REQUIREMENTS/SPECIFICATIONS TPIM-T2 TPIM-T4REQUIREMENTS/SPECIFICATIONS TPIM-F2 Parameter Typical Worst Worst Case TypicalValue Case Budget REQUIREMENTS/SPECIFICATIONS TPIM-F3 TPIM-F3Parameter Typical Minimum Maximum REQUIREMENTS/SPECIFICATIONS General Specifications Power Supply RequirementsOutput Min. Load Max. Load Max Power Environmental RequirementsREQUIREMENTS/SPECIFICATIONS Safety ServicePhysical Unpacking the Trxi Attaching the Strain Relief BracketInstalling the Trxi Attaching the Strain ReliefInstalling the Trxi in the Rack Rack Mounting the TrxiWall Mounting the Trxi Free-Standing Installation Installation Setting the Ring Speed Switch Ring Speed Switch SettingsInstallation Setting the Nvram Switch Installation Connecting the Trxi to the Power Source Connecting the Network Lobe Port CablingConfiguration Examples for TRXI-24 and TRXI-44 LNK TPIM-T4 Installation Installing the Tpim RI/RO Modules Setting the TPIM’s Phantom Switch and RI/RO Switch Top ViewInstalling a Tpim to the Trxi 12. Installing a TpimConnecting a Twisted Pair Segment to the TPIM-T1 Connecting a Twisted Pair Segment to the TPIM-T2 or TPIM-T4 Installation LNK Finishing the Installation Chapter Testing and Troubleshooting Checking the InstallationTesting and Troubleshooting Using Lanview TRXI-24TOKEN Ring HUB with LanviewTesting and Troubleshooting LCD Display LCDStatic System Messages Displayed Message CommentsAlarm Messages Displayed Messages CommentsFailure or Error Messages Unsaved Initialization MessagesNormal Unsaved Initialization Messages Saved System Messages Displayed MessageChapter Local Management Local Management Management Terminal Requirements Attaching the Management TerminalSetting the Management Terminal Setup Parameters Display SetupGeneral Setup SetupModem Cable Configuration and Setup RJ45 COM 2 PortLocal Management Accessing Local Management Trxi Local ManagementLocal Management Using Local Management Main MenuSelecting a Menu Option Exiting a Local Management ScreenExiting Your Local Management Session System Level Screen System DateSystem Time IP AddressSetting the System Date COM 1 ApplicationCOM 2 Application Clear All NvramSetting the System Time Setting the IP AddressSetting the Subnet Mask Setting the Clear All Nvram Field Setting the Enable Beacon Recovery FieldSnmp Community Names Screen Access Component NameCommunity Name Editing the Community Name FieldEnable Traps Snmp Traps ScreenTrap Destination Trap Community NameSetting Snmp Traps Ring Security Screen Security Mode Station AddressStn Edit SAVE/EXECUTE NextscreenPreviousscreen ReturnBuilding the Allowed List Adding Stations to the Station Address Allowed ListChanging the Ring Security Mode Deleting Stations from the Station Address Allowed ListDevice Statistics Screen Device StatisticsInterface Isolating Errors Ring Information Ports Enabled NON-ISOLATING ErrorsLost Frame Errors Ring NumberFrame Copied Errors Rcvr Congestion ErrorsToken Errors Frequency ErrorsSelecting the Device Statistics Counter Mode Setting the Refresh FieldEnable All Ports Chassis Status View ScreenPort Status TempSetting the Enable All Ports Option Setting the Operational/Administrative Mode OptionOperational ReturnComponent Status View Screen 11. Component Status View ScreenSnmp Tools Screen GET SETGetnext WalkSecurity Access Level Getting and Setting OIDsCommunity Name Local Management Scrolling Through MIB OIDs Local Management Local Management Power Supply Cord GermanSpanish French