Cabletron Systems 1000, 1200 manual Configuring the Cyberswitch Options, Snmp

Page 36

EXAMPLE NETWORKS

CONFIGURE THE CYBERSWITCH

Note: The software should have already been installed and you should see the system prompt before proceeding with these steps.

Using the detailed instructions for these steps found in the Simple Remote Bridging chapter, complete the following configuration steps.

Start the CFGEDIT program

Select physical resources

Select to add a resource

Select Switch type to be 4ESS

Select to add a line

Enter “Line1” as the line name

Select slot 1, port 1

Add Data Links

Choose Auto TEI Negotiation

Enter SPID Value

Enter Directory Number for Data Link

Enter Maximum Number of Digits to Verify

Repeat “Add Data Links” for second Data Link

Repeat “Select to add a line” for each additional line

The following sections provide instructions for completing the remaining configuration steps.

CONFIGURING THE CYBERSWITCH OPTIONS

To begin the configuration of the system options, press 2 at the Main Menu. The following options menu will then be displayed:

Options Menu:

1)Bridging

2)IP

3)IPX Routing

4)AppleTalk

5)SNMP

6)PPP

7)Call Control Options

8)Default Line Protocol

9)Log Options

10)Compression

Select function from above or <RET> for previous menu:

For this example, we only need IP routing enabled. IP routing is already enabled as fault, so no change is necessary.

For this example, the only other IP information we need to configure is for IP interfaces. No static routes are needed because Router 1 supports RIP, which eliminates the need to manually configure a static route. The next section will provide the instructions needed to configure the necessary IP interfaces.

36 CyberSWITCH

Image 36
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Resources LinesBridging and Routing Information IP RoutingConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Device Information Calling ISDN, FR, etc. InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Options Configuring the SecurityConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Configuring the Cyberswitch Options SnmpConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation IP Routing Network with Remote Bridge Devices Business AssumptionsIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS For Site BridgingLAN2 For Site 918105551234 Configure SITE1 Configuring the System OptionsConfiguring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configure SITE2 Configuring SITE2 OptionsConfiguring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing Configure Devices ADD IPX WAN DeviceAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 Appletalk Routing AppleTalk Routing/Port InformationPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index