Cabletron Systems 1200, 1000 manual Finishing the Security Configuration

Page 73

IP ROUTING NETWORK WITH PPP DEVICES

Configure SITE1

Next, select the RIP Propagation Control. This controls how a static route is propagated via RIP. Press 3 to propagate only when the Next Hop is connected. This flag indicates that the route information is propagated via RIP only when the next hop router is connected to SITE1.

The screen interaction will resemble the following:

Is this route the DEFAULT Route (Y or N)? N

Enter the Destination IP Address in dotted decimal notation or <RET> to cancel? 128.3.0.0

Enter the number of significant bits for the subnet mask [default = 16] <RET>

Enter the Next Hop IP Address in dotted decimal notation or ‘0’ if the Next Hop is an unnumbered link, or <RET> to cancel? 0

Enter the device name of the Next Hop device or <RET> to cancel? SITE2

Enter the Metric value for this route [default = 2]? <RET>

RIP Propagation Control:

1)Do Not Propagate.

2)Always Propagate.

3)Propagate only when the Next Hop is connected.

Enter a RIP Propagation Scheme from the above menu [default = 3]? <RET>

A summary of the values you have entered for this static route will be displayed. Respond to the prompt asking you if you wish to add this static route. If you add this static route the following screen will then be displayed:

Current STATIC

ROUTE Configuration:

 

 

id Destination

Address

Mask

Next Hop

Metric

-- -------------------

------------------- ------------------- ------

1

128.3.0.0

 

255.255.0.0

(SITE2)

2

(1) Add, (2) Change, (3) Delete, (4) Display a STATIC ROUTE or press <RET> for previous menu?

SITE1 does not need a static route to the Router on its LAN. This is because SITE1 supports RIP, and the Router supports RIP. RIP is a protocol that exchanges routing information among IP devices. Return to the Main Menu. We now need to complete SITE1’s Security configuration.

FINISHING THE SECURITY CONFIGURATION

This example uses device security, and the remote devices are configured in the on-node authentication database. We enabled device security using an on-node authentication database when we configured the SITE2 device.

To complete the security configuration, press 3 at the Main CFGEDIT Menu. The Security Menu will then be displayed. The sections below provide instructions for configuring the remaining security information.

Workgroup Remote Access Switch 73

Image 73
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Lines ResourcesIP Routing Bridging and Routing InformationConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Calling ISDN, FR, etc. Information Device InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Security Configuring the OptionsConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Snmp Configuring the Cyberswitch OptionsConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation Business Assumptions IP Routing Network with Remote Bridge DevicesIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS Bridging For SiteLAN2 For Site 918105551234 Configuring the System Options Configure SITE1Configuring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configuring SITE2 Options Configure SITE2Configuring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing ADD IPX WAN Device Configure DevicesAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 AppleTalk Routing/Port Information Appletalk RoutingPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index