Cabletron Systems 1000, 1200 manual Base Data Rate 64000 bps Initial Maximum 384000 bps

Page 70

EXAMPLE NETWORKS

Press 5 to enter the first dial out number. A phone number must be defined for each remote device that will be dialed. This number includes any prefix digits, area codes, or extensions as required to dial the destination device. It is possible to specify two phone numbers for the remote device. For this example, we will only be entering one phone number, 913135553232, which is the phone number for SITE2.

After all of the ISDN configuration has been completed, the ISDN Configuration Menu will be displayed as follows:

Device ISDN Menu: (Device = "SITE2")

1)

ISDN Line Protocol

"PPP (Point to Point Protocol)"

2)

Base Data Rate

"64000 bps"

3)

Initial

Data Rate

"64000 bps"

4)

Maximum

Data Rate

"384000 bps"

5)

Dial Out Phone Number(s)

"913135553232"

6)

Subaddress

""

7)

Profile

Name

"Default_Profile"

8)

H0 Call

Support

DISABLED

Select function from above or <RET> for previous menu?

Return to the Device Table Menu.

At the Device Table Menu, press 4 to enter the authentication information needed for this device. The authentication information needed for each device depends on the device type.

For device “SITE2”, because we will be configuring CHAP security, we opt to configure a CHAP secret (ikcd98s). After the secret has been entered, the Device Authentication Configuration Menu will appear as follows:

Device Authentication Menu: (Device = "SITE2")

PPP:

 

 

1)

PAP Password

""

2)

CHAP Secret

"ikcd98s"

3)

Outbound Authentication

ENABLED

4)

User Level Authentication

DISABLED

IP Host (RFC 1294):

 

5)

IP Host Id

""

HDLC Bridge:

 

6)

Bridge Ethernet Address

""

7)

Bridge Password

""

ISDN:

 

 

8)

Calling Line Id(s)

""

Select function from above or <RET> for previous menu:

Again, return to the Device Table Menu.

Next, press 5 to enter the IP Information for device SITE2. SITE2 uses an unnumbered link, so we will enter the IP address as 0.0.0.0.

70 CyberSWITCH

Image 70
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Resources LinesBridging and Routing Information IP RoutingConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Device Information Calling ISDN, FR, etc. InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Options Configuring the SecurityConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Configuring the Cyberswitch Options SnmpConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation IP Routing Network with Remote Bridge Devices Business AssumptionsIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS For Site BridgingLAN2 For Site 918105551234 Configure SITE1 Configuring the System OptionsConfiguring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configure SITE2 Configuring SITE2 OptionsConfiguring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing Configure Devices ADD IPX WAN DeviceAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 Appletalk Routing AppleTalk Routing/Port InformationPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index