Cabletron Systems 1200, 1000 manual Configuring Appletalk Port Information

Page 99

APPLETALK ROUTING NETWORK

Configure the CyberSWITCH

CONFIGURING APPLETALK PORT INFORMATION

For this example, we need to configure both a LAN and a WAN UnNumbered AppleTalk port. The LAN AppleTalk port represents SITE1’s connection to its LAN AppleTalk network, allowing SITE1 to exchange packets with the two MACs on the LAN. The WAN UnNumbered port creates a logical AppleTalk network over WAN that uses unnumbered point-to-point links, allowing SITE1 to exchange packets with SITE2.

We will begin with configuring the LAN AppleTalk port. Select AppleTalk Ports from the AppleTalk Routing Menu. Then, press 1 to add a port. You will then be prompted for port information as shown below:

AppleTalk Port Type:

1)LAN

2)WAN

3)WAN (UnNumbered)

4)WAN (Mac Dial In)

Enter a port type from the above menu or <RET> to cancel? 1

Enter the port name or <RET> to cancel ? lanport1

Enter the LAN port number or <RET> to cancel? 1

AppleTalk Network Type:

1)Extended Network

2)NonExtended Network

Enter a network type from the above menu or <RET> to cancel? 1

Enter the AppleTalk network range. Use 0-0 to place the port into discovery mode or <RET> to cancel? 10-13

Enter the suggested AppleTalk address [default = None] ? <RET>

Enter the default zone name or <RET> to cancel ? SITE1.Engineering

Use the following information to clarify each of the port information entries:

port type:

Press 1 to select the LAN port type (this indicates that the system is physically connected to an Ethernet LAN segment.

port name:

The port name is a 1 to 16 character device-defined string that will identify the LAN port to the system administrator. Enter lanport1 for the port name.

port number:

Enter 1 for the port number of the AppleTalk LAN port. This is the port number on the Ethernet resource to which the physical LAN is connected.

AppleTalk network type:

Choices are: extended or nonextended network. The extended network allows addressing of more than 254 nodes and supports multiple zones, whereas the nonextended network allows up to 254 nodes and supports only one zone.This network requires a range of network numbers and multiple zones. Select the extended network type.

Workgroup Remote Access Switch 99

Image 99
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Lines ResourcesIP Routing Bridging and Routing InformationConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Calling ISDN, FR, etc. Information Device InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Security Configuring the OptionsConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Snmp Configuring the Cyberswitch OptionsConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation Business Assumptions IP Routing Network with Remote Bridge DevicesIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS Bridging For SiteLAN2 For Site 918105551234 Configuring the System Options Configure SITE1Configuring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configuring SITE2 Options Configure SITE2Configuring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing ADD IPX WAN Device Configure DevicesAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 AppleTalk Routing/Port Information Appletalk RoutingPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index