Cabletron Systems 1200, 1000 manual Configuring Static Routes

Page 71

IP ROUTING NETWORK WITH PPP DEVICES

Configure SITE1

The following screen will be displayed after all information for device SITE2 has been entered:

Current Device Table (Sorted by Device Name in Ascending ASCII Order)

id DEVICE NAME

-----------------------------

1

"SITE2"

(1)Add, (2) Change, (3) Delete, (4) Display a Device or press <RET> for previous menu?

Now that device SITE2 has been configured, we can add the needed static route:

Return to the Main Menu.

Press 2 to display the Options Menu.

Press 2 to display the IP Routing Menu.

Press 3 to add a static route.

CONFIGURING STATIC ROUTES

SITE1 requires one static route. This static route will give SITE1 access to SITE2 and its associated resources. The diagram below illustrates this needed static route, and also the default route needed by SITE2 to gain access to SITE1 and its associated resources.

To begin the static route configuration, press 3 at the IP menu, then press 1 to add a Static Route.

First, you will be asked if the route is the default route. Press N when asked if this is the default route.

Next, enter the destination IP address of the network to which you want to connect. You should enter SITE2’s LAN Interface IP address 128.3.0.0.

After you enter the IP address of the LAN, you will be prompted for the Subnet Mask for the address. Press <return> to accept the default of “16” significant bits.

You will then be prompted for the Next Hop device name for the static route. The Next Hop device name names the device that provides access to the network on which SITE2 resides. For this static route, SITE2 is the Next Hop. Because we have configured an IP WAN unnumbered interface for SITE1 and SITE2, SITE2 is an unnumbered link for SITE1. For unnumbered links you should enter 0 for the Next Hop address. This interface will provide the gateway to this network.

When prompted, enter SITE2 as the device name of the next hop device.

Workgroup Remote Access Switch 71

Image 71
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Lines ResourcesIP Routing Bridging and Routing InformationConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Calling ISDN, FR, etc. Information Device InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Security Configuring the OptionsConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Snmp Configuring the Cyberswitch OptionsConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation Business Assumptions IP Routing Network with Remote Bridge DevicesIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS Bridging For SiteLAN2 For Site 918105551234 Configuring the System Options Configure SITE1Configuring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configuring SITE2 Options Configure SITE2Configuring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing ADD IPX WAN Device Configure DevicesAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 AppleTalk Routing/Port Information Appletalk RoutingPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index