Cabletron Systems 1200, 1000 manual Enabled

Page 25

REMOTE BRIDGING NETWORK WITH SECURITY

Configure the CyberSWITCH

Device Name? Mike Mann

After the new device name has been specified, a screen similar to the following is displayed.

Device Table Menu: (Device = "Mike Mann")

1)ISDN

2)Frame Relay

3)X.25

4)Authentication

5)IP

6)IPX

7)AppleTalk

8)Bridging

9)Compression

Select function from above or <RET> for previous menu:

Information for the new device may be configured in any order. You have control over how much information is specified for each device, and the order in which it is entered.

We will begin by specifying the type of device. We need to determine if the device will use ISDN Line Protocol (choice 1), Frame Relay (choice 2), or X.25 (choice 3).This device is an ISDN device, so we will press 1 for “ISDN Information” from the Device Table Configuration Menu.

The ISDN Configuration Menu will then be displayed with the preconfigured default values:

Device ISDN Menu: (Device = "Mike Mann")

1)

ISDN Line Protocol

"PPP (Point to Point Protocol)"

2)

Base Data Rate

"64000 bps"

3)

Initial

Data Rate

"64000 bps"

4)

Maximum

Data Rate

"128000 bps"

5)

Dial Out Phone Number(s)

""

6)

Subaddress

""

7)

Profile

Name

"Default_Profile"

8)

H0 Call

Support

ENABLED

Select function from above or <RET> for previous menu:

We do not want to use the default ISDN Line Protocol of PPP. Press 1 to configure this device’s ISDN line protocol. The device Mike Mann uses HDLC protocol, so we will press 2:

Device ISDN Line Protocol Menu: (Device = "Mike Mann")

1)PPP (Point to Point Protocol)

2)HDLC Bridge

3)IP Host (RFC1294)

Select option to associate with device "Mike Mann",

or "0" to disable ISDN access for this device [default = 1]? 2

The only other item on the Device ISDN Line Protocol Menu that this type of device needs is the maximum data rate. We will accept the default value of 128,000 bps. No changes are required. Return to the Device Table Menu.

Workgroup Remote Access Switch 25

Image 25
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with PPP Devices Index Example Networks Simple Remote Bridging Network Lines ResourcesIP Routing Bridging and Routing InformationConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Calling ISDN, FR, etc. Information Device InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configuring the Security Configuring the OptionsConfiguring the Security Level Enabled PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Snmp Configuring the Cyberswitch OptionsConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation Business Assumptions IP Routing Network with Remote Bridge DevicesIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Example Networks WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS Bridging For SiteLAN2 For Site 918105551234 Configuring the System Options Configure SITE1Configuring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes SITE1 needs default route to SITE2 CSX1200 Host #2 Finishing the Security Configuration Configuring SITE2 Options Configure SITE2Configuring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing ADD IPX WAN Device Configure DevicesAuthentication Information Configure System Options Add a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Isdn SITE1 AppleTalk Routing/Port Information Appletalk RoutingPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index