Extron electronic IPL T S Series manual Setting the Internet Protocol IP Address

Page 27

Lighting

Control

 

 

 

 

 

RS-232

 

 

 

 

 

Extron

 

 

 

 

 

IPL T S4

 

 

 

COM

3

Ethernet Control

 

COM

1

COM

2

Interface

 

 

2

 

 

 

093012052

COM

 

 

 

 

 

 

 

 

 

UID#

 

 

 

 

 

LAN

 

 

 

 

RS-232

POWER

 

 

 

 

TCP/IP

NetworkRS-232

Ethernet

Remote User

Control and

Administrator

Monitoring

Laptop DVD

Extron

MAV 62

Matrix Switcher

Extron

Extron

MediaLink or

Other Controller

Projector

VCR

Figure 3-2 — Typical IPL T S interface operating configuration

2.

Connect the other end of the serial cable to the display or switching device to

 

be controlled through the IPL T S.

Setting the Internet Protocol (IP) Address

The IPL T S Series units have a factory default IP address of 192.168.254.254. This IP address must be changed to an address that will operate on your local network.

There are three ways to change the IP address setting:

•Add Device > Auto Config IP option in Global Configurator

•IPL T S unit’s embedded Web pages

•Address Resolution Protocol (ARP) command

Before you begin:

1.

Obtain a valid IP address for your IPL T S Series device from your A/V

 

system’s network administrator.

2.

Write down the unit’s MAC address (a 12-digit number) found on a label on

 

the rear panel of the unit (ex: 00-05-A6-01-0A-74).

3.

If the unit is not at it’s factory default IP address (192.168.254.254), perform a

 

Mode 4 reset:

 

a.

Hold down the Reset button until the Power LED blinks twice (6

 

 

seconds), then release.

 

b.

Press and release the Reset button again within 1 second.

 

 

The Power LED blinks quickly four times, confirming the Mode 4 reset,

 

 

which returns the unit to its factory default IP address.

IPL T S Series • Connection and Configuration

3-3

Page 26 Page 28
Image 27
Page 26 Page 28
Contents IP Link Ethernet Control Interfaces IPL T S SeriesSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFCC Class a Notice IPL T S SeriesIi IPL T S Series Or on a rack Quick Start IPL T S SeriesOn a projector Under a deskQS-2 IPL T S Series Quick Start Preliminary Table of ContentsTable of Contents, cont’d One Introduction About This ManualAbout the IPL T S Series Interface IPL T S6 FeaturesIntroduction, cont’d Two Mounting the IPL T S Interface Installation and OperationInstallation Overview IPL T S Series Installation and OperationVersaTools 19 1U Rack Shelf Mounting optionsRack mounting an IPL T S Series interface Mounting Type Kit PNFurniture mount kit for IPL T S2, S4, S6 Furniture or projector mountingFurniture mount kit for IPL T S1 Projector mount kit for IPL T S1Mounting the interface Rear Panel Features and CablingPreliminary PowerEthernet/LAN Serial CommunicationLink LED a lit green LED indicates a good LAN connection Pin Function RS-232 RS-422 RS-485 IPL T S Series InstallationUID # The unique user ID number MAC address of the unit for Front panel indicatorsOperation IdentificationLED is not lit, the connection speed is 10 Mbps Resetting the unitUnit later in this chapter for more information RX LEDs a green LED indicates data is being received byMode Activation Result Reset Mode Comparison/SummaryInstallation and Operation, cont’d Three Ethernet connection Connection and ConfigurationConnecting the Hardware IPL T S Series Connection and ConfigurationSetting the Internet Protocol IP Address Hold down the Reset button until the Power LED blinks twiceRear panel of the unit ex 00-05-A6-01-0A-74 Advanced options of the Add Device dialog are displayed, Setting the IP address using Global ConfiguratorAdd Device dialog box opens see figure Enter a unique device name in the Display Name fieldIP address Subnet mask Default gateway blank Setting the IP address using embedded Web pagesInternet Protocol TCP/IP Properties dialog box Setting the IP address using the ARP command Start All Programs Accessories Command PromptArp sIP addressMAC address Click the Download GCSW2XX.exe button Configuration using Global ConfiguratorGlobal Configurator Configuration using Embedded Web PagesWeb server Password dialog box Connecting via the Web server pagesSystem Status ConfigurationSystem Settings IP Settings Date/Time SettingsPort Settings 12 System Settings screenEmail Alerts PasswordsFile Management Firmware UpgradeTo run DataViewer Configuration using DataViewerTo download DataViewer Scroll to the description of DataViewerDataViewer application opens see figure 19 Communication Setup dialog boxFour IPL T S Series Communication and Control Using the command/response tableCommunication and Control Programmer’s Guide for Telnet and Web BrowsersX1% = Domain name e.g., extron.com, icia.org Symbol definitionsCopyright information Password informationE17 System timed out E22 Busy Error responsesAscii to Decimal Conversion Table CommunicationBidirectional serial data port Series Communication and ControlCpnX!CtyX2  X!* X2%, X2, X2&, X2*CP WX! %2A X2% %2CX2 %2CX2X2%, X2, X2&, X2   X!*X2CYEthernet data port X5,X5#,X2X6 TC Series Communication and ControlFirmware version, part number and information requests X1! Series Communication and Control X4%SM  X4%, X4, X4&CR WX4%%2CX4%2CX4&CR IprX4%,X4,X4&  X4%CR X4, X4&  X1& ,X1% CM WX1$ %2CX1% CM IpmX1$ ,X1%  X4%,X7,X4&SM WX4%%2CX7%2CX4&SM X1$ ,X1% ,X7# ,X7$ CM IpmX1$ ,X1% ,X7# ,X7$X1#  X1@CNX1@  X1#CTX6$,X1$  X2@  X6$,X1$ EB  WX6$%2CX1$EB Bmd X6$,X1$   X6$ EB X5@ Password and security settings X3# CA  X3# CU WX3# CURemap port designations Directories Stream files via Telnet or RS-232 IP address is reset to Subnet mask is reset toDiscussed in Resetting the Unit Server Side Includes SSI This example the N command is used to requestCustomization Custom Web pagesHref=index.html?cmd=xInput #1/a Query stringExample Code examples6b Browser view of previous Html source code Reserved characters URL encodingSerial pass-through redirect mode Advanced Serial Port ControlUnsafe characters To initiate direct port access using DataViewer Direct port access ports 2001 throughHardware connection Click OK. The DataViewer commands window opensTo end the direct access session, close DataViewer Serial BridgingIPL T S4 Serial bridge configurationTroubleshooting Power connectionsData connections IPL T S Series Communication and Control Communication and Control, cont’d Specifications, Part Numbers, Accessories Serial, 10-pole captive screw Specifications, Part Numbers, AccessoriesSpecifications IPL T S Series Specifications, Part Numbers, AccessoriesOr VersaTools 1U, 3.5 deep rack shelf RSF 123, #60-190-20 Mounting Rack mountAccessories Part number Part Numbers and AccessoriesOptional accessories Included parts Replacement part NumberAppendix B Glossary GlossaryIPL T S Series Glossary IPL T S Series Glossary Extron’s Warranty Extron China Extron EuropeExtron Asia Extron Japan
Related manuals
Manual 29 pages 23.94 Kb

IPL T S Series specifications

The Extron IPL T SFI244 is a sophisticated control system that is designed to streamline the management and operation of audiovisual equipment in a variety of environments, including conference rooms, classrooms, and auditoriums. This model falls under the IPL T S Series, renowned for its superior performance and user-friendly interface, making it a popular choice for integrators and users alike.

One of the standout features of the IPL T SFI244 is its advanced interface. It boasts an intuitive touch panel that enables users to manage multiple devices from a single control point, significantly simplifying the AV experience. The system supports a wide range of functions, including source selection, volume control, and the management of lighting and screen mechanisms. This centralized control helps to enhance collaboration and communication, particularly in educational and corporate settings.

The IPL T SFI244 integrates seamlessly with a variety of Extron technologies, including the GlobalViewer Enterprise, providing real-time monitoring and management capabilities. This web-based software solution gives administrators the ability to control AV systems remotely, ensuring optimal performance and minimizing downtime.

Another key characteristic of the IPL T SFI244 is its versatility. It incorporates various input and output options, such as HDMI, VGA, and audio connections, to accommodate different audiovisual equipment. This flexibility allows for easy integration into existing setups, catering to diverse applications and user preferences.

In terms of design, the IPL T SFI244 is engineered with reliability and durability in mind. It is equipped with features that enhance its performance in professional environments, including programmable button layouts that can be customized by users. This personalization ensures that the control system meets specific operational requirements, further enhancing the user experience.

Furthermore, the IPL T SFI244 is built with energy efficiency in mind, utilizing technologies that reduce power consumption without compromising performance. This eco-friendly approach not only supports sustainability initiatives but also contributes to long-term cost savings for organizations.

In summary, the Extron IPL T SFI244 is a comprehensive control solution that combines advanced technology, user-friendly features, and robust performance. Its ability to integrate with various AV equipment, coupled with its customizable interface and reliability, makes it an excellent choice for a wide range of applications, paving the way for more efficient and effective audiovisual management.
Top Page Image Contents