Extron electronic IPL T S Series manual Direct port access ports 2001 through

Page 65

CO

M 1

CO

M 2

UID

# 093012052

LAN

 

POWER

12V MAX

.5A

 

TCP/IP

Network

Ethernet

Remote User

Control &

Administrator

Monitoring

Extron

IPL T S2

Ethernet Control

Interface

RS-232

RS-232

Laptop

DVD

VCR

Extron

Extron MediaLink or Other Controller

Projector

Figure 4-8 — Pass-through mode

In the figure above, a MediaLink® controller connected to the IPL T S2’s serial port 1 (COM1) is controlling a projector connected to serial port 2 (COM2).

Serial pass-through is enabled or disabled through the “Com Configuration” tab of a device within Extron’s Global Configurator software.

Advanced users can use the pass-through SIS command as well. See the “Command/response table for Simple Instruction Set (SIS) commands”, earlier in this chapter, for detailed command descriptions.

Direct port access (ports 2001 through 2006)

Direct port access allows a direct, one-to-one connection to any of the serial ports using a TCP/IP connection. When a TCP session is initiated to port 2001 (COM1) through port 2006 (COM6), all data sent and received passes directly to and from that port without any processing. Set serial port parameters (baud rate, parity, etc.) within the IPL T S Series unit prior to using direct access. (See “Port Settings” in chapter 3).

NThe reserved TCP port numbers (2001-2006) are default assignments.

To initiate direct port access using DataViewer:

1.If necessary, set serial port parameters (baud rate, parity, etc.) within the

IPL T S unit. (See “Port Settings” in chapter 3.)

2.Launch the DataViewer software program.

3. Click the TCP/IP tab on the Communication Setup dialog box.

4.Complete the fields with the appropriate IP address and the TCP/IP port number (2001-2006), as shown below.

NA password is not required for direct port access.

IPL T S Series • Communication and Control 4-25

Page 64 Page 66
Image 65
Page 64 Page 66
Contents IP Link Ethernet Control Interfaces IPL T S SeriesSafety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice IPL T S SeriesIi IPL T S Series On a projector Quick Start IPL T S SeriesUnder a desk Or on a rackQS-2 IPL T S Series Quick Start Preliminary Table of ContentsTable of Contents, cont’d One About the IPL T S Series Interface IntroductionAbout This Manual IPL T S6 FeaturesIntroduction, cont’d Two Installation Overview Installation and OperationIPL T S Series Installation and Operation Mounting the IPL T S InterfaceRack mounting an IPL T S Series interface Mounting optionsMounting Type Kit PN VersaTools 19 1U Rack ShelfFurniture mount kit for IPL T S1 Furniture or projector mountingProjector mount kit for IPL T S1 Furniture mount kit for IPL T S2, S4, S6Mounting the interface Rear Panel Features and CablingPreliminary PowerLink LED a lit green LED indicates a good LAN connection Ethernet/LANSerial Communication Pin Function RS-232 RS-422 RS-485 IPL T S Series InstallationOperation Front panel indicatorsIdentification UID # The unique user ID number MAC address of the unit forUnit later in this chapter for more information Resetting the unitRX LEDs a green LED indicates data is being received by LED is not lit, the connection speed is 10 MbpsMode Activation Result Reset Mode Comparison/SummaryInstallation and Operation, cont’d Three Connecting the Hardware Connection and ConfigurationIPL T S Series Connection and Configuration Ethernet connectionRear panel of the unit ex 00-05-A6-01-0A-74 Setting the Internet Protocol IP AddressHold down the Reset button until the Power LED blinks twice Add Device dialog box opens see figure Setting the IP address using Global ConfiguratorEnter a unique device name in the Display Name field Advanced options of the Add Device dialog are displayed,IP address Subnet mask Default gateway blank Setting the IP address using embedded Web pagesInternet Protocol TCP/IP Properties dialog box Arp sIP addressMAC address Setting the IP address using the ARP commandStart All Programs Accessories Command Prompt Click the Download GCSW2XX.exe button Configuration using Global ConfiguratorGlobal Configurator Configuration using Embedded Web PagesWeb server Password dialog box Connecting via the Web server pagesSystem Settings ConfigurationIP Settings Date/Time Settings System StatusPort Settings 12 System Settings screenEmail Alerts PasswordsFile Management Firmware UpgradeTo download DataViewer Configuration using DataViewerScroll to the description of DataViewer To run DataViewerDataViewer application opens see figure 19 Communication Setup dialog boxFour Communication and Control Using the command/response tableProgrammer’s Guide for Telnet and Web Browsers IPL T S Series Communication and ControlX1% = Domain name e.g., extron.com, icia.org Symbol definitionsCopyright information Password informationE17 System timed out E22 Busy Error responsesBidirectional serial data port CommunicationSeries Communication and Control Ascii to Decimal Conversion TableX2%, X2, X2&, X2   X!* X2%, X2, X2&, X2*CP WX! %2A X2% %2CX2 %2CX2 X!*X2CY CpnX!CtyX2X6 TC X5,X5#,X2Series Communication and Control Ethernet data portSeries X1! Communication and Control Firmware version, part number and information requests X4%CR  X4%, X4, X4&CR WX4%%2CX4%2CX4&CR IprX4%,X4,X4& X4, X4&   X4%SM X1$ ,X1% ,X7# ,X7$ CM  X4%,X7,X4&SM WX4%%2CX7%2CX4&SMIpmX1$ ,X1% ,X7# ,X7$  X1& ,X1% CM WX1$ %2CX1% CM IpmX1$ ,X1%X1@  X1@CN X1#CT X1# X6$,X1$ EB  WX6$%2CX1$EB Bmd X6$,X1$  X2@  X6$ EB  X6$,X1$  X3# CA Password and security settings X3# CU WX3# CU X5@Remap port designations Directories Stream files via Telnet or RS-232 Discussed in Resetting the Unit IP address is reset toSubnet mask is reset to Customization This example the N command is used to requestCustom Web pages Server Side Includes SSIHref=index.html?cmd=xInput #1/a Query stringExample Code examples6b Browser view of previous Html source code Reserved characters URL encodingUnsafe characters Serial pass-through redirect modeAdvanced Serial Port Control To initiate direct port access using DataViewer Direct port access ports 2001 throughTo end the direct access session, close DataViewer Click OK. The DataViewer commands window opensSerial Bridging Hardware connectionIPL T S4 Serial bridge configurationData connections TroubleshootingPower connections IPL T S Series Communication and Control Communication and Control, cont’d Specifications, Part Numbers, Accessories Specifications Specifications, Part Numbers, AccessoriesIPL T S Series Specifications, Part Numbers, Accessories Serial, 10-pole captive screwOr VersaTools 1U, 3.5 deep rack shelf RSF 123, #60-190-20 Mounting Rack mountOptional accessories Part Numbers and AccessoriesIncluded parts Replacement part Number Accessories Part numberAppendix B IPL T S Series Glossary GlossaryGlossary IPL T S Series Glossary Extron’s Warranty Extron Asia Extron EuropeExtron Japan Extron China
Related manuals
Manual 29 pages 23.94 Kb

IPL T S Series specifications

The Extron IPL T SFI244 is a sophisticated control system that is designed to streamline the management and operation of audiovisual equipment in a variety of environments, including conference rooms, classrooms, and auditoriums. This model falls under the IPL T S Series, renowned for its superior performance and user-friendly interface, making it a popular choice for integrators and users alike.

One of the standout features of the IPL T SFI244 is its advanced interface. It boasts an intuitive touch panel that enables users to manage multiple devices from a single control point, significantly simplifying the AV experience. The system supports a wide range of functions, including source selection, volume control, and the management of lighting and screen mechanisms. This centralized control helps to enhance collaboration and communication, particularly in educational and corporate settings.

The IPL T SFI244 integrates seamlessly with a variety of Extron technologies, including the GlobalViewer Enterprise, providing real-time monitoring and management capabilities. This web-based software solution gives administrators the ability to control AV systems remotely, ensuring optimal performance and minimizing downtime.

Another key characteristic of the IPL T SFI244 is its versatility. It incorporates various input and output options, such as HDMI, VGA, and audio connections, to accommodate different audiovisual equipment. This flexibility allows for easy integration into existing setups, catering to diverse applications and user preferences.

In terms of design, the IPL T SFI244 is engineered with reliability and durability in mind. It is equipped with features that enhance its performance in professional environments, including programmable button layouts that can be customized by users. This personalization ensures that the control system meets specific operational requirements, further enhancing the user experience.

Furthermore, the IPL T SFI244 is built with energy efficiency in mind, utilizing technologies that reduce power consumption without compromising performance. This eco-friendly approach not only supports sustainability initiatives but also contributes to long-term cost savings for organizations.

In summary, the Extron IPL T SFI244 is a comprehensive control solution that combines advanced technology, user-friendly features, and robust performance. Its ability to integrate with various AV equipment, coupled with its customizable interface and reliability, makes it an excellent choice for a wide range of applications, paving the way for more efficient and effective audiovisual management.
Top Page Image Contents