Page 69
2.Try to “ping” the unit by entering “ping 192.168.254.254” at the DOS command prompt, or use the IP or Web address provided to you by your system administrator. If you get no response:
a.Make sure your unit is using the appropriate subnet mask (check with your system administrator).
b. Make sure your PC does not have a software firewall program that might block the IP address of the unit.
3.If contact is established with the unit, but the unit’s Web pages cannot be accessed by your Web browser, verify (in the Options or Preferences menu) that your Web browser is configured for direct network connection and is not set up to use a proxy server.
If you are still experiencing problems, call the Extron S3 Sales & Technical Support Hotline.
IPL T S Series • Communication and Control 4-29
Contents
IP Link Ethernet Control Interfaces
IPL T S Series
Safety Instructions English
Precautions
Consignes de Sécurité Français
Sicherheitsanleitungen Deutsch
FCC Class a Notice
IPL T S Series
Ii IPL T S Series
On a projector
Quick Start IPL T S Series
Under a desk
Or on a rack
QS-2 IPL T S Series Quick Start
Preliminary
Table of Contents
Table of Contents, cont’d
One
Introduction
About This Manual
About the IPL T S Series Interface
IPL T S6
Features
Introduction, cont’d
Two
Installation Overview
Installation and Operation
IPL T S Series Installation and Operation
Mounting the IPL T S Interface
Rack mounting an IPL T S Series interface
Mounting options
Mounting Type Kit PN
VersaTools 19 1U Rack Shelf
Furniture mount kit for IPL T S1
Furniture or projector mounting
Projector mount kit for IPL T S1
Furniture mount kit for IPL T S2, S4, S6
Mounting the interface
Rear Panel Features and Cabling
Preliminary
Power
Ethernet/LAN
Serial Communication
Link LED a lit green LED indicates a good LAN connection
Pin Function RS-232 RS-422 RS-485
IPL T S Series Installation
Operation
Front panel indicators
Identification
UID # The unique user ID number MAC address of the unit for
Unit later in this chapter for more information
Resetting the unit
RX LEDs a green LED indicates data is being received by
LED is not lit, the connection speed is 10 Mbps
Mode Activation Result
Reset Mode Comparison/Summary
Installation and Operation, cont’d
Three
Connecting the Hardware
Connection and Configuration
IPL T S Series Connection and Configuration
Ethernet connection
Setting the Internet Protocol IP Address
Hold down the Reset button until the Power LED blinks twice
Rear panel of the unit ex 00-05-A6-01-0A-74
Add Device dialog box opens see figure
Setting the IP address using Global Configurator
Enter a unique device name in the Display Name field
Advanced options of the Add Device dialog are displayed,
IP address Subnet mask Default gateway blank
Setting the IP address using embedded Web pages
Internet Protocol TCP/IP Properties dialog box
Setting the IP address using the ARP command
Start All Programs Accessories Command Prompt
Arp sIP addressMAC address
Click the Download GCSW2XX.exe button
Configuration using Global Configurator
Global Configurator
Configuration using Embedded Web Pages
Web server Password dialog box
Connecting via the Web server pages
System Settings
Configuration
IP Settings Date/Time Settings
System Status
Port Settings
12 System Settings screen
Email Alerts
Passwords
File Management
Firmware Upgrade
To download DataViewer
Configuration using DataViewer
Scroll to the description of DataViewer
To run DataViewer
DataViewer application opens see figure
19 Communication Setup dialog box
Four
Communication and Control
Using the command/response table
Programmer’s Guide for Telnet and Web Browsers
IPL T S Series Communication and Control
X1% = Domain name e.g., extron.com, icia.org
Symbol definitions
Copyright information
Password information
E17 System timed out E22 Busy
Error responses
Bidirectional serial data port
Communication
Series Communication and Control
Ascii to Decimal Conversion Table
X2%, X2, X2&, X2
X!* X2%, X2, X2&, X2*CP WX! %2A X2% %2CX2 %2CX2
X!*X2CY
CpnX!CtyX2
X6 TC
X5,X5#,X2
Series Communication and Control
Ethernet data port
Series
X1!
Communication and Control
Firmware version, part number and information requests
X4%CR
X4%, X4, X4&CR WX4%%2CX4%2CX4&CR IprX4%,X4,X4&
X4, X4&
X4%SM
X1$ ,X1% ,X7# ,X7$ CM
X4%,X7,X4&SM WX4%%2CX7%2CX4&SM
IpmX1$ ,X1% ,X7# ,X7$
X1& ,X1% CM WX1$ %2CX1% CM IpmX1$ ,X1%
X1@
X1@CN
X1#CT
X1#
X6$,X1$ EB WX6$%2CX1$EB Bmd X6$,X1$
X2@
X6$ EB
X6$,X1$
X3# CA
Password and security settings
X3# CU WX3# CU
X5@
Remap port designations
Directories
Stream files via Telnet or RS-232
IP address is reset to
Subnet mask is reset to
Discussed in Resetting the Unit
Customization
This example the N command is used to request
Custom Web pages
Server Side Includes SSI
Href=index.html?cmd=xInput #1/a
Query string
Example
Code examples
6b Browser view of previous Html source code
Reserved characters
URL encoding
Serial pass-through redirect mode
Advanced Serial Port Control
Unsafe characters
To initiate direct port access using DataViewer
Direct port access ports 2001 through
To end the direct access session, close DataViewer
Click OK. The DataViewer commands window opens
Serial Bridging
Hardware connection
IPL T S4
Serial bridge configuration
Troubleshooting
Power connections
Data connections
IPL T S Series Communication and Control
Communication and Control, cont’d
Specifications, Part Numbers, Accessories
Specifications
Specifications, Part Numbers, Accessories
IPL T S Series Specifications, Part Numbers, Accessories
Serial, 10-pole captive screw
Or VersaTools 1U, 3.5 deep rack shelf RSF 123, #60-190-20
Mounting Rack mount
Optional accessories
Part Numbers and Accessories
Included parts Replacement part Number
Accessories Part number
Appendix B
Glossary
Glossary
IPL T S Series Glossary
IPL T S Series Glossary
Extron’s Warranty
Extron Asia
Extron Europe
Extron Japan
Extron China