Extron electronic FOX T USW 103 Fiber Optic Connector, RS-232 Over Fiber and Alarm Connector

Page 11

The following table shows the audio format that is sent over the fiber connection when a specific audio format is not specified (see the Input audio selection SIS command on page 15 to switch the active audio source).

Selected Video

HDMI Embedded

Analog Audio

Audio Sent Over Fiber

Input

Audio Present

Present

 

 

 

 

 

VGA

N/A

Yes

Analog audio

 

 

 

 

VGA

N/A

No

No audio

 

 

 

 

HDMI

Yes

No

HDMI embedded audio

 

 

 

 

HDMI

Yes

Yes

HDMI embedded audio

 

 

 

 

HDMI

No

Yes

Analog audio

 

 

 

 

HDMI

No

No

No audio

 

 

 

 

Fiber Optic Connector

DFiber optic connector — For one-way video, audio, and serial communication from the FOX T USW 103 to a receiver, connect a fiber optic cable between the Tx port on the FOX T USW 103 and the Rx port on a receiver.

To return serial data from a receiver to the FOX T USW 103 or for HDCP-compliance, connect a fiber optic cable between the Rx port on the FOX T USW 103 and the Tx port on the receiver (see Wiring for Fiber Communication on page 7).

NOTES:

Ensure the proper fiber optic cable is used. Typically, singlemode fiber optic cable has a yellow jacket and multimode fiber optic cable has an orange or aqua jacket.

Only one fiber optic cable, transmitter-Tx-to-receiver-Rx, is required for video, audio, serial command transmission, but the HDMI signal output on the receiver will not be HDCP-compliant and the FOX T USW 103 will not receive RS-232 reports from the controlled device.

The Link LED indicators light when there is light presence on either fiber optic port.

RS-232 Over Fiber and Alarm Connector

ERS-232 Over Fiber port — To pass serial command signals to a receiver (for serial control of a projector, for example), connect a host device to the switcher via the leftmost poles (Tx, Rx, and G) of this 5-pole captive screw connector (see Wiring for RS-232 Over Fiber and Alarm Communication on page 8 for wiring configurations).

Alarm port For remote monitoring of the status of fiber optic link 2, connect a custom or furnished monitoring device to the switcher via the rightmost poles (1 and 2) of this 5-pole captive screw connector (see Wiring for RS-232 Over Fiber and Alarm Communication on page 8).

RS-232

OVER FIBER ALARM

Tx Rx G

1

2

RS-232

OVER FIBER ALARM

Tx Rx G

1

2

NOTE: Pins 1 and 2 short within the switcher when link 2 does not detect any connection.

FOX T USW 103 Universal Switcher • Installation

5

Image 11
Contents FOX T USW Safety Instructions English Chinese Simplified(简体中文) Class 1 Laser Product FCC Class a Notice FDA/IEC 60825-1 RequirementsNotifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideContents FOX T USW 103 Universal Switcher Contents System Compatibility IntroductionAbout This Guide About the FOX T USWHDCP-compliance Key FeaturesContact closure remote control availability Typical FOX T USW 103 Application Application DiagramMounting the FOX T USW InstallationRear Panel Features Input ConnectorsRS-232 Over Fiber and Alarm Connector Fiber Optic ConnectorMaking Connections Control ConnectorsPower Connector Connecting Hdmi ConnectorsWiring for Fiber Communication Wiring for Remote Contact Closure Communication Wiring for RS-232 Over Fiber and Alarm CommunicationPower Connector Wiring Wiring the Power SupplyFront Panel Button Combinations for Device Modes Front Panel FeaturesOperation Front Panel OperationSelecting an Input Initial Power UpEnabling Auto Switch Mode Enabling Normal Switch ModeHost-to-device and device-to-host communication SIS Configuration ControlSimple Instruction Set Control SIS Programming GuideSymbol definitions Error responsesUsing the command and response table for SIS commands VGA PC SIS Audio Configuration Command and Response Tables for SIS CommandsInput Switching Horizontal start Picture Adjustment Analog OnlyPixel phase Total pixelsAdvanced Configurations Status request Device nameInformation requests SFP module View internal temperatureFactory reset Upload firmwareTo download the software from the website Installing the SoftwareTo install the software from the DVD FOX Extenders Control ProgramStarting the Software Using the SoftwareFile menu Top MenuTools Menu ConnectDisconnect ExitUnit Info Reset UnitTo update firmware Update FirmwareTrace Window RefreshExtron Home ContentsCheck for Updates About FOX Extenders Control Program Dialog Box AboutStatus panel Main ScreenControl tab Input Selection panelVGA Video Adjustment Panel VGA Video Adjustment panelHdcp panel Audio Adjustment panelConfiguration Tab Advanced Tab Plus Mode Transmission panelVGA Input Video Format panel Audio Input Selection panelSave Edid panel Advanced Configuration panelEdid Configuration Tab Assigned Edid panelImport Edid Panel Import Edid panelExport Edid Panel Export Edid panelMounting Kits Reference InformationMounting Tabletop UseDownloading Extron Firmware Loader Installing Firmware LoaderUpdating Firmware Downloading Firmware from the Extron Website Downloading FirmwareAdd Device... Window Installing Firmware with Firmware LoaderExtron Warranty