Extron electronic FOX T USW 103 manual Introduction, About This Guide, About the FOX T USW

Page 7

Introduction

This section contains general information about this guide and the FOX T USW 103 Universal Switcher with an integrated fiber optic transmitter, selected device features, and a typical application diagram. Topics in this section include:

About This Guide

About the FOX T USW 103

Key Features

Application Diagram

About This Guide

This guide describes installation, operation, and control procedures, and reference information for the FOX T USW 103 Universal Switcher with an integrated fiber optic transmitter. In this guide, the terms “FOX T USW 103” and “switcher” are used interchangeably to refer to the FOX T USW 103 Universal Switcher with an integrated fiber optic transmitter in singlemode or multimode.

About the FOX T USW 103

The Extron FOX T USW 103 is a three input universal switcher with an integrated fiber optic transmitter that provides long haul transmission of HDCP-compliant HDMI, RGBHV, or HD component video; stereo audio; and RS-232 signals over fiber optic cabling. The switcher delivers pixel-for-pixel transmission of images up to 1920x1200, including HDTV 1080p/60.

To configure and control the FOX T USW 103, connect a host device, such as a computer, and enter Simple Instruction Set (SIS) commands (see Simple Instruction Set Control on page 12) or use the FOX Extenders Control Program (see FOX Extenders Control Program on page 20).

System Compatibility

The FOX T USW 103 operates in either of two modes, selected under RS-232 control, for compatibility with other, non-HDMI, units:

Plus — Supports resolutions up to 1920x1200 @ 60Hz. The fiber optic output of the switcher can be received only by one of six receivers: a FOXBOX HDMI Rx, FOXBOX DVI Plus Rx, PowerCage HDMI Rx, PowerCage FOX DVI Plus Rx, FOXBOX SR HDMI, and PowerCage FOX SR HDMI.

Non-Plus— Supports resolutions up to 1600x1200 and 1080p @ 60 Hz (including HDTV 1080p/60 Hz), is HDCP compliant, and does not contain embedded audio (analog audio is still supported). The fiber optic output of the transmitter can be received by any FOXBOX, PowerCage FOX, and FOX 500 VGA and DVI unit, including the Plus and non-Plus units.

Cable Transmission Modes

The transmitter is further categorized by the type of fiber optic cable, multimode

(FOX T USW 103 MM) or singlemode (FOX T USW 103 SM), which define the effective range of transmission:

Multimode — Long distance, up to 2 km (6,560 feet) (depending on the fiber cable)

Singlemode — Very long distance, up to 30 km (18.75 miles)

FOX T USW 103 Universal Switcher • Introduction

1

Image 7
Contents FOX T USW Safety Instructions English Chinese Simplified(简体中文) Class 1 Laser Product FCC Class a Notice FDA/IEC 60825-1 RequirementsNotifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideContents FOX T USW 103 Universal Switcher Contents System Compatibility IntroductionAbout This Guide About the FOX T USWContact closure remote control availability Key FeaturesHDCP-compliance Typical FOX T USW 103 Application Application DiagramMounting the FOX T USW InstallationRear Panel Features Input ConnectorsRS-232 Over Fiber and Alarm Connector Fiber Optic ConnectorMaking Connections Control ConnectorsPower Connector Connecting Hdmi ConnectorsWiring for Fiber Communication Wiring for Remote Contact Closure Communication Wiring for RS-232 Over Fiber and Alarm CommunicationPower Connector Wiring Wiring the Power SupplyFront Panel Button Combinations for Device Modes Front Panel FeaturesOperation Front Panel OperationSelecting an Input Initial Power UpEnabling Auto Switch Mode Enabling Normal Switch ModeHost-to-device and device-to-host communication SIS Configuration ControlSimple Instruction Set Control SIS Programming GuideUsing the command and response table for SIS commands Error responsesSymbol definitions VGA PC SIS Input Switching Command and Response Tables for SIS CommandsAudio Configuration Horizontal start Picture Adjustment Analog OnlyPixel phase Total pixelsAdvanced Configurations Information requests Device nameStatus request SFP module View internal temperatureFactory reset Upload firmwareTo download the software from the website Installing the SoftwareTo install the software from the DVD FOX Extenders Control ProgramStarting the Software Using the SoftwareFile menu Top MenuTools Menu ConnectDisconnect ExitUnit Info Reset UnitTo update firmware Update FirmwareTrace Window RefreshCheck for Updates ContentsExtron Home About FOX Extenders Control Program Dialog Box AboutStatus panel Main ScreenControl tab Input Selection panelVGA Video Adjustment Panel VGA Video Adjustment panelConfiguration Tab Audio Adjustment panelHdcp panel Advanced Tab Plus Mode Transmission panelVGA Input Video Format panel Audio Input Selection panelSave Edid panel Advanced Configuration panelEdid Configuration Tab Assigned Edid panelImport Edid Panel Import Edid panelExport Edid Panel Export Edid panelMounting Kits Reference InformationMounting Tabletop UseUpdating Firmware Installing Firmware LoaderDownloading Extron Firmware Loader Downloading Firmware from the Extron Website Downloading FirmwareAdd Device... Window Installing Firmware with Firmware LoaderExtron Warranty