Extron electronic FOX T USW 103 manual Front Panel Features, Front Panel Operation

Page 16

Operation

This section describes the front panel features of the FOX T USW 103 and describes front panel operations. Topics in this section include:

Front Panel Features

Front Panel Operation

Front Panel Features

AUTO

 

 

 

1

 

 

2

 

3

 

 

STATUS

 

 

SWITCH

 

 

 

 

 

 

 

 

 

1

2

3

 

 

 

CONFIG

 

 

 

 

 

 

 

 

SIGNAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDCP

FOX T USW 103

 

 

 

 

 

MODE

NORMAL

 

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a b

c

d

Figure 8. FOX T USW 103 Front Panel Features

AAuto Switch LED — Lights when the transmitter is in auto switch mode.

BConfig port — Connect a host device to the mini USB Config port for remote control.

CInput selection buttons — Select inputs 1 through 3 or modes of operation. The corresponding LEDs light to indicate the active input.

DStatus LEDs — The Signal LEDs light to indicate the signal presence of each input. The HDCP LEDs light when the signal on the corresponding input is HDCP compliant. Input 1 (the VGA connector) does not have an HDCP LED.

Front Panel Operation

The three buttons with corresponding LEDs on the front panel (labeled Mode, Normal, and Auto) are used to manually select inputs 1 through 3 or enable and disable device modes. The LEDs indicate status and the currently selected input.

To enable or disable executive, auto switch, or normal switch mode from the front panel, press and hold a combination of input selection buttons simultaneously until the appropriate LEDs blink (see the table below for the different button combinations).

Front Panel Button Combinations for Device Modes

Mode

Button Combinations

Executive

1, 2, and 3

 

 

Auto switch

1 and 3

(prioritize the highest numbered active input)

 

 

 

Normal switch (default)

1 and 2

 

 

The front panel operations can also be performed remotely with SIS commands or the FOX Extenders Control Program (see Simple Instruction Set Control on page 12 or

FOX Extenders Control Program on page 20).

FOX T USW 103 Universal Switcher • Operation 10

Image 16
Contents FOX T USW Safety Instructions English Chinese Simplified(简体中文) FCC Class a Notice FDA/IEC 60825-1 Requirements Class 1 Laser ProductSpecifications Availability Software CommandsConventions Used in this Guide NotificationsContents FOX T USW 103 Universal Switcher Contents Introduction About This GuideAbout the FOX T USW System CompatibilityContact closure remote control availability Key FeaturesHDCP-compliance Application Diagram Typical FOX T USW 103 ApplicationInstallation Rear Panel FeaturesInput Connectors Mounting the FOX T USWFiber Optic Connector RS-232 Over Fiber and Alarm ConnectorControl Connectors Power ConnectorConnecting Hdmi Connectors Making ConnectionsWiring for Fiber Communication Wiring for RS-232 Over Fiber and Alarm Communication Wiring for Remote Contact Closure CommunicationWiring the Power Supply Power Connector WiringFront Panel Features OperationFront Panel Operation Front Panel Button Combinations for Device ModesInitial Power Up Enabling Auto Switch ModeEnabling Normal Switch Mode Selecting an InputSIS Configuration Control Simple Instruction Set ControlSIS Programming Guide Host-to-device and device-to-host communicationUsing the command and response table for SIS commands Error responsesSymbol definitions VGA PC SIS Input Switching Command and Response Tables for SIS CommandsAudio Configuration Picture Adjustment Analog Only Pixel phaseTotal pixels Horizontal startAdvanced Configurations Information requests Device nameStatus request View internal temperature Factory resetUpload firmware SFP moduleInstalling the Software To install the software from the DVDFOX Extenders Control Program To download the software from the websiteUsing the Software Starting the SoftwareTop Menu File menuConnect DisconnectExit Tools MenuReset Unit Unit InfoUpdate Firmware To update firmwareRefresh Trace WindowCheck for Updates ContentsExtron Home About About FOX Extenders Control Program Dialog BoxMain Screen Status panelInput Selection panel Control tabVGA Video Adjustment panel VGA Video Adjustment PanelConfiguration Tab Audio Adjustment panelHdcp panel Plus Mode Transmission panel VGA Input Video Format panelAudio Input Selection panel Advanced TabAdvanced Configuration panel Edid Configuration TabAssigned Edid panel Save Edid panelImport Edid panel Import Edid PanelExport Edid panel Export Edid PanelReference Information MountingTabletop Use Mounting KitsUpdating Firmware Installing Firmware LoaderDownloading Extron Firmware Loader Downloading Firmware Downloading Firmware from the Extron WebsiteInstalling Firmware with Firmware Loader Add Device... WindowExtron Warranty