Extron electronic FOX T USW 103 manual FCC Class a Notice FDA/IEC 60825-1 Requirements

Page 3

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference; the user must correct the interference at his own expense.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

FDA/IEC 60825-1 Requirements

CLASS 1 LASER PRODUCT

Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 5, dated June 24, 2007.

The product is intended to be used with the fiber optic cables fully installed.

This product meets the applicable requirements of IEC 60825-1, Edition 1 (2007).

Any service to this product must be carried out by Extron Electronics and its qualified service personnel.

Copyright

© 2013 Extron Electronics. All rights reserved.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of

RGB Systems, Inc. or Extron Electronics:

Registered Trademarks (®)

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IP Intercom,

IP Link, Key Minder, LockIt, MediaLink, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System Integrator, TouchLink, VLock, VersaTools, VNMatrix, VoiceLift, WallVault, WindoWall, XTP, XTP Systems

Registered Service Mark(SM) : S3 Service Support Solutions

Trademarks ()

AAP, AFL (AccuRate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), AutoImage, CDRS (Class D Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QSFPC (QuickSwitch Front Panel Controller), ScopeTrigger, SIS, Simple Instruction Set, SkewFree, SpeedNav, TeamWork, TripleAction Switching, XTRA, ZipCaddy, ZipClip

Image 3
Contents FOX T USW Safety Instructions English Chinese Simplified(简体中文) Class 1 Laser Product FCC Class a Notice FDA/IEC 60825-1 RequirementsNotifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideContents FOX T USW 103 Universal Switcher Contents System Compatibility IntroductionAbout This Guide About the FOX T USWKey Features Contact closure remote control availabilityHDCP-compliance Typical FOX T USW 103 Application Application DiagramMounting the FOX T USW InstallationRear Panel Features Input ConnectorsRS-232 Over Fiber and Alarm Connector Fiber Optic ConnectorMaking Connections Control ConnectorsPower Connector Connecting Hdmi ConnectorsWiring for Fiber Communication Wiring for Remote Contact Closure Communication Wiring for RS-232 Over Fiber and Alarm CommunicationPower Connector Wiring Wiring the Power SupplyFront Panel Button Combinations for Device Modes Front Panel FeaturesOperation Front Panel OperationSelecting an Input Initial Power UpEnabling Auto Switch Mode Enabling Normal Switch ModeHost-to-device and device-to-host communication SIS Configuration ControlSimple Instruction Set Control SIS Programming GuideError responses Using the command and response table for SIS commandsSymbol definitions VGA PC SIS Command and Response Tables for SIS Commands Input SwitchingAudio Configuration Horizontal start Picture Adjustment Analog OnlyPixel phase Total pixelsAdvanced Configurations Device name Information requestsStatus request SFP module View internal temperatureFactory reset Upload firmwareTo download the software from the website Installing the SoftwareTo install the software from the DVD FOX Extenders Control ProgramStarting the Software Using the SoftwareFile menu Top MenuTools Menu ConnectDisconnect ExitUnit Info Reset UnitTo update firmware Update FirmwareTrace Window RefreshContents Check for UpdatesExtron Home About FOX Extenders Control Program Dialog Box AboutStatus panel Main ScreenControl tab Input Selection panelVGA Video Adjustment Panel VGA Video Adjustment panelAudio Adjustment panel Configuration TabHdcp panel Advanced Tab Plus Mode Transmission panelVGA Input Video Format panel Audio Input Selection panelSave Edid panel Advanced Configuration panelEdid Configuration Tab Assigned Edid panelImport Edid Panel Import Edid panelExport Edid Panel Export Edid panelMounting Kits Reference InformationMounting Tabletop UseInstalling Firmware Loader Updating FirmwareDownloading Extron Firmware Loader Downloading Firmware from the Extron Website Downloading FirmwareAdd Device... Window Installing Firmware with Firmware LoaderExtron Warranty