Extron electronic FOX T USW 103 manual SIS Configuration Control, Simple Instruction Set Control

Page 18

SIS Configuration

and Control

This section describes remote control of the FOX T USW 103 through SIS commands and basic installation instructions for the FOX Extenders Control Program (see to the FOX Extenders Control Program Help File for operation details).

To enable serial control of the FOX T USW 103, use a computer running the HyperTerminal or Extron DataViewer utility, or a control system. Connect the computer to the

FOX T USW 103 through the front panel Config port or the rear panel RS-232 connector.

The protocol for the RS-232 port is as follows: 9600 baud, no parity, 8 data bits, 1 stop bit, no flow control

Simple Instruction Set Control

SIS Programming Guide

Host-to-device and device-to-host communication

SIS commands consist of one or more characters per field. No special characters are required to begin or end a command sequence. When the FOX T USW 103 determines that a command is valid, it executes the command and sends a response to the host device. All responses from the switcher or receiver to the host end with a carriage return and a line feed (CR/LF = ]), which signals the end of the response character string. A string is one or more characters.

Device-initiated messages

When a local event occurs, the device responds by sending a message to the host. The device-initiated message may depend on whether the device is multimode or singlemode. They are listed below.

© Copyright 2013, Extron Electronics FOX T USW 103 MM, Vx.xx, 60-1229-11 © Copyright 2013, Extron Electronics FOX T USW 103 SM, Vx.xx, 60-1229-12

Vx.xx is the firmware version number.

Reconfig]

The FOX T USW 103 returns this message when there is any change to the input frequency on the currently selected input.

1LnkX%2LnkX%VidX%AudX%X1)TX]

The FOX T USW 103 returns this status message whenever a change in the fiber link, video, or audio connection occurs. X% indicates whether the link is present or not present

(0 = not present, 1 = present) and X1) represents whether the device is multimode or singlemode (MM = multimode, SM = singlemode).

FOX T USW 103 Universal Switcher • Remote Control 12

Image 18
Contents FOX T USW Safety Instructions English Chinese Simplified(简体中文) FCC Class a Notice FDA/IEC 60825-1 Requirements Class 1 Laser ProductConventions Used in this Guide Specifications AvailabilitySoftware Commands NotificationsContents FOX T USW 103 Universal Switcher Contents About the FOX T USW IntroductionAbout This Guide System CompatibilityKey Features Contact closure remote control availabilityHDCP-compliance Application Diagram Typical FOX T USW 103 ApplicationInput Connectors InstallationRear Panel Features Mounting the FOX T USWFiber Optic Connector RS-232 Over Fiber and Alarm ConnectorConnecting Hdmi Connectors Control ConnectorsPower Connector Making ConnectionsWiring for Fiber Communication Wiring for RS-232 Over Fiber and Alarm Communication Wiring for Remote Contact Closure CommunicationWiring the Power Supply Power Connector WiringFront Panel Operation Front Panel FeaturesOperation Front Panel Button Combinations for Device ModesEnabling Normal Switch Mode Initial Power UpEnabling Auto Switch Mode Selecting an InputSIS Programming Guide SIS Configuration ControlSimple Instruction Set Control Host-to-device and device-to-host communicationError responses Using the command and response table for SIS commandsSymbol definitions VGA PC SIS Command and Response Tables for SIS Commands Input SwitchingAudio Configuration Total pixels Picture Adjustment Analog OnlyPixel phase Horizontal startAdvanced Configurations Device name Information requestsStatus request Upload firmware View internal temperatureFactory reset SFP moduleFOX Extenders Control Program Installing the SoftwareTo install the software from the DVD To download the software from the websiteUsing the Software Starting the SoftwareTop Menu File menuExit ConnectDisconnect Tools MenuReset Unit Unit InfoUpdate Firmware To update firmwareRefresh Trace WindowContents Check for UpdatesExtron Home About About FOX Extenders Control Program Dialog BoxMain Screen Status panelInput Selection panel Control tabVGA Video Adjustment panel VGA Video Adjustment PanelAudio Adjustment panel Configuration TabHdcp panel Audio Input Selection panel Plus Mode Transmission panelVGA Input Video Format panel Advanced TabAssigned Edid panel Advanced Configuration panelEdid Configuration Tab Save Edid panelImport Edid panel Import Edid PanelExport Edid panel Export Edid PanelTabletop Use Reference InformationMounting Mounting KitsInstalling Firmware Loader Updating FirmwareDownloading Extron Firmware Loader Downloading Firmware Downloading Firmware from the Extron WebsiteInstalling Firmware with Firmware Loader Add Device... WindowExtron Warranty