Extron electronic ISM 482 manual Configuration, RS-232 connection

Page 24

RS-232 connection

7Remote port — Connect a host device, such as a computer or touch panel control, to the integration scaling matrix switcher via this 9-pin D connector for serial RS-232 control (figure 2-9).

	Pin	RS-232	Function	5	1
	1	—	Not used

	2	TX	Transmit data
	3	RX	Receive data	9	6
	4	—	Not used
				Female
	5	Gnd	Signal ground	1	5
	6	—	Not used
	7	—	Not used
	8	—	Not used	6	9
	9	—	Not used
				Male

Figure 2-9 — Remote port pin assignments

See chapter 4, “Programmer’s Guide”, for definitions of the SIS commands and chapter 5, “Switcher Software” to install and use the control software.

Configuration

The ISM can be configured using either the front panel controls, the SIS, or the Windows Control program. See chapter 3, “Operation”, chapter 4, “Programmer’s Guide”, and chapter 5, “Switcher Software”.

Integration Scaling Matrix Switcher • Installation

2-9

Image 24

Contents ISM Precautions FCC Class B Notice Quick Start Integration Scaling Matrix Switcher Integration Scaling Matrix Switcher Quick Start QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Integration Scaling Matrix Switcher Quick StartTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About the Switcher Integration Scaling Matrix Switcher IntroductionIntroductiontroduction, cont’d About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Rack mountingMounting the switcher Mounting instructionsInstallation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs videoOptional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable Configuration RS-232 connectionInstallation, cont’d Three Front Panel Controls and Indicators Integration Scaling Matrix Switcher OperationOperationeration, cont’d Video/Audio selection button and LEDsOutput buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuOperation, cont’d 10 Advanced Configuration menu flowchart Blue-Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Centering controls to position the imageTroubleshooting Optimizing the AudioGeneral checks Specific problems Problem CauseOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Switcher-Initiated Messages Power-upProgrammer’s Guide, cont’d Ties creationX2 Col RGB delay PAL film modeAutomated adjustments Test patternHost-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command/response table for SIS commands cont’d Command Ascii Command Response Additional descriptionHorizontal detail filter RGB and component video inputs User presets Verbose mode Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Command/response table for IP SIS commandsX2 Reconfig message may not be Command/response table for advanced instruction set commands Command Hex Command ResponseFive Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Ethernet protocol settings Software operation via EthernetSwitcher Software, cont’d Using the control programWindows Control program window Using the help program Button-Label GeneratorUsing the software To run the Button-Label Generator program, click StartSwitcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Changing the RGB delay Ethernet Operation, cont’dControl Creating a tieUsing Blue-Only mode Executive modeFreezing the output Outputting a test patternSystem Configuration System ConfigurationAdministration fields ISM IP Settings fieldsISM IP Address field ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationEthernet Operation, cont’d Output resolution Output rateOutput format Output polaritySeven Maintenance and Modifications Opening and Closing the SwitcherGrounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware UpgradeInstalling a DVI Output Card DVI output card connector opening and socket J14Output DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Connecting as a Telnet Client Ethernet Connection, cont’dTelnet tips OpenEscape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb