Extron electronic ISM 482 Installationstallation, cont’d, Mounting the Switcher, Rack mounting

Page 17

Installationstallation, cont’d

Mounting the Switcher

Four uninstalled rubber feet are included with the switcher. If you are going to rack mount the switcher, mount it before you cable it (see “Rack mounting”, below), and do not install the rubber feet. If you are not rack mounting the switcher, see “Tabletop placement” below.

Tabletop placement

For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the switcher.

Rack mounting

UL requirements

The following Underwriters Laboratories (UL) requirements pertain to the installation of the switcher into a rack (figure 2-1).

1. Elevated operating ambient temperature — If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature.

Therefore, install the switcher in an environment compatible with the maximum ambient temperature (Tma = +122 °F, +50 °C) specified by Extron.

2. Reduced air flow — Install the equipment in a rack so that the amount of air flow required for safe operation of the equipment is not compromised.

3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading.

4. Circuit overloading — Connect the equipment to the supply circuit and consider the effect that circuit overloading might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

5.Reliable earthing (grounding) — Maintain reliable grounding of rack- mounted equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

2-2 Integration Scaling Matrix Switcher • Installation

Image 17

Contents ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Integration Scaling Matrix Switcher Introduction About the SwitcherIntroductiontroduction, cont’d About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Mounting the Switcher Installationstallation, cont’dTabletop placement Rack mountingMounting instructions Mounting the switcherInput connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connectionsOptional output connection Choosing a network cable Cabling and RJ-45 connector wiringWiring the network cable RS-232 connection ConfigurationInstallation, cont’d Three Integration Scaling Matrix Switcher Operation Front Panel Controls and IndicatorsOperationeration, cont’d Video/Audio selection button and LEDsFront panel input label window Output buttons and LEDsInput buttons, LEDs, and label window Black/Mute button and LEDs Picture adjustment buttonsOperation, cont’d Menu control buttons Adjustment knobsLCD display Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuOperation, cont’d 10 Advanced Configuration menu flowchart RGB Delay submenu Blue-Only Mode and Edge Smoothing submenuTest Pattern submenu Blanking submenuPixel Phase submenu Enhanced Mode submenuPAL Film Mode submenu Reset submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustmentsAdjust knobs have no mechanical limits to their rotation Front panel security lockout Executive modeIP information Optimizing the VideoCentering controls to position the image Setting up a DVD sourceGeneral checks TroubleshootingOptimizing the Audio Problem Cause Specific problemsOperation, cont’d Four Ethernet Link Integration Scaling Matrix Switcher Programmer’s GuideRS-232 Link Ethernet connection SymbolsDefault address Power-up Switcher-Initiated MessagesProgrammer’s Guide, cont’d Ties creationX2 Col PAL film mode RGB delayAutomated adjustments Test patternUsing the command/response table Host-to-Switcher InstructionsSwitcher error responses Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’dHorizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commandsCommand/response table for IP SIS commands Command/response table for special function SIS commandsX2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commandsFive Control Software for Windows Installing the softwareIntegration Scaling Matrix Switcher Switcher Software Software operation via Ethernet Ethernet protocol settingsUsing the control program Switcher Software, cont’dWindows Control program window Button-Label Generator Using the help programTo run the Button-Label Generator program, click Start Using the softwareSwitcher Software, cont’d Six Loading the Startup Control Integration Scaling Matrix Switcher Ethernet OperationEthernetOperation,cont’d Control Ethernet Operation, cont’d Changing the RGB delayControl Creating a tieExecutive mode Using Blue-Only modeFreezing the output Outputting a test patternSystem Configuration System ConfigurationISM IP Settings fields Administration fieldsISM IP Address field ISM Name fieldFile Management File ManagementI/O Configuration Input configurationEthernet Operation, cont’d Output rate Output resolutionOutput polarity Output formatSeven Opening and Closing the Switcher Maintenance and ModificationsGrounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’dDVI output card connector opening and socket J14 Installing a DVI Output CardOutput DVI board installation AAppendix a Cabling Integration Scaling Matrix Switcher Ethernet ConnectionEthernet Connection Pinging to determine the Web IP address Determining Default AddressesPinging to determine the switcher’s IP address Ethernet Connection, cont’d Connecting as a Telnet ClientTelnet tips OpenLocal echo Escape character and Esc keySet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb