Extron electronic ISM 482 manual Quick Start Integration Scaling Matrix Switcher

Page 4

Tip Sleeve

Tip Sleeve

Unbalanced Input

(high impedance)

Tip

Ring Sleeve (s) Tip Ring

Balanced Input (high impedance)

Quick Start — Integration Scaling Matrix Switcher

Installation

Step 1

Turn off power to the ISM ISM 482 and the input and output devices, and remove the power cords from them.

Step 2

If desired, install an optional DVI output card into the switcher. See chapter 7, “Maintenance and Modifications”.

Step 3

Install four rubber feet on the bottom of the ISM or mount the ISM in a rack.

482

ISM

INPUTS

Step 5

Cable the switcher for audio input. Each input has a 3.5 mm, 5-pole captive screw connector

for balanced or

unbalanced stereo or mono audio input. Connectors are included with each switcher, but

you must supply the

audio cable. High impedance is generally over 800 ohms.

Step 6

	Connect RGB video displays to
	the Output 1 and Output 2	R	R
	female BNC and 15-pin HD
	connectors. Connect the	G	G
	various video formats to the	G	G
	various video formats to the
	BNCs as shown.
	Both output connector	B	B
	Both output connector
	types output the same
	video signal and the
	same sync format.	H/HV	H/HV
	same sync format.

Step 7	V	V
Cable the switcher for audio	RGBHV	RGBS
output. Each output has a	Video	Video
output. Each output has a

3.5 mm, 5-pole captive screw

connector that outputs the selected unamplified, line level audio. Connect an audio device, such as an audio amplifier or powered speakers.

Step 4

Connect up to eight computer/RGB video, component video, S-video, or composite video sources to these female BNC input connectors.

The figure below shows how to connect the various video formats.

NO GROUND	AUDIO
NO GROUND
NO GROUND.
Unbalanced Output
Tip	AUDIO
Tip	AUDIO
Ring
Sleeve (s)
Ring

Balanced Output

CAUTION Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

R/R-Y	R/R-Y	R/R-Y	R/R-Y	R/R-Y
G/Y	G/Y	G/Y	G/Y	G/Y
VID	VID	VID	VID	VID
B/C	B/C	B/C	B/C	B/C
B-Y	B-Y	B-Y	B-Y	B-Y
H/HV	H/HV	H/HV	H/HV	H/HV
V	V	V	V	V
RGBHV	RGBS or	RGsB or	S-Video	Composite
Video	RGBcvS	Component		Video
	Video	Video

Step 8

If the optional DVI output card is	9
installed, connect a DVI video display
to the output 1 DVI connector.	17	1
	24	8

Integration Scaling Matrix Switcher • Quick Start QS-1

Image 4

Contents ISM Precautions FCC Class B Notice Quick Start Integration Scaling Matrix Switcher Integration Scaling Matrix Switcher Quick Start QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Integration Scaling Matrix Switcher Quick StartTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About the Switcher Integration Scaling Matrix Switcher IntroductionIntroductiontroduction, cont’d About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Rack mountingMounting the switcher Mounting instructionsCabling and Rear Panel Views Installation, cont’dInput connections Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs videoOptional output connection Wiring the network cable Cabling and RJ-45 connector wiringChoosing a network cable Configuration RS-232 connectionInstallation, cont’d Three Front Panel Controls and Indicators Integration Scaling Matrix Switcher OperationOperationeration, cont’d Video/Audio selection button and LEDsInput buttons, LEDs, and label window Output buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuOperation, cont’d 10 Advanced Configuration menu flowchart Blue-Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Centering controls to position the imageOptimizing the Audio TroubleshootingGeneral checks Specific problems Problem CauseOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Default address SymbolsEthernet connection Switcher-Initiated Messages Power-upProgrammer’s Guide, cont’d Ties creationX2 Col RGB delay PAL film modeAutomated adjustments Test patternSwitcher error responses Host-to-Switcher InstructionsUsing the command/response table Programmer’s Guide, cont’d Command/response table for SIS commands cont’d Command Ascii Command Response Additional descriptionHorizontal detail filter RGB and component video inputs User presets Verbose mode Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Command/response table for IP SIS commandsX2 Reconfig message may not be Command/response table for advanced instruction set commands Command Hex Command ResponseFive Integration Scaling Matrix Switcher Switcher Software Installing the softwareControl Software for Windows Ethernet protocol settings Software operation via EthernetSwitcher Software, cont’d Using the control programWindows Control program window Using the help program Button-Label GeneratorUsing the software To run the Button-Label Generator program, click StartSwitcher Software, cont’d Six EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoading the Startup Control Control Changing the RGB delay Ethernet Operation, cont’dControl Creating a tieUsing Blue-Only mode Executive modeFreezing the output Outputting a test patternSystem Configuration System ConfigurationAdministration fields ISM IP Settings fieldsISM IP Address field ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationEthernet Operation, cont’d Output resolution Output rateOutput format Output polaritySeven Maintenance and Modifications Opening and Closing the SwitcherGrounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware UpgradeInstalling a DVI Output Card DVI output card connector opening and socket J14Output DVI board installation AAppendix a Ethernet Connection Integration Scaling Matrix Switcher Ethernet ConnectionCabling Pinging to determine the switcher’s IP address Determining Default AddressesPinging to determine the Web IP address Connecting as a Telnet Client Ethernet Connection, cont’dTelnet tips OpenEscape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb