Extron electronic ISM 482 manual Picture adjustments flowchart

Page 41

Operation, cont’d

Picture adjustments

The picture adjustments allow you to fine tune the image quality of the selected input. When you press one of the Picture Adjustments buttons (Color/Tint, Brightness/Contrast, Size, Center, or Filter) once, the corresponding image adjustment menu for the selected output (lit Output LED) image appears on the LCD screen. Select the other output using the Output buttons to call the image adjustment menu for the other output. In either screen, adjustments can then be made by rotating the Adjust knob or the Adjust knob. Picture adjustment settings are stored in nonvolatile memory; when the switcher is powered down and powered up, the settings are restored.

Adjust an image for centering, sizing, brightness, contrast, color, tint, zoom, or detail as follows (figure 3-13):

	Extron Electronics		Extron Electronics
	ISM 482		ISM 482
Power	Integration		60-425-01		Display
on	Scaling Matrix	2 sec.	Version xxxx	2 sec.	Cycle

COLOR/		BRT/		SIZE		CENTER		FILTER
TINT		CONT
TINT		CONT

Output #1		Output #1			Output #1	Output #1		Output #1
Color	Tint	Brightness	Contrast	Horz	Size Vert	Horz Center	Vert	Horz Filter	Vert
127	128	063	063	450	400	500	550	3	7
								10 sec.
								timeout
NOTE Press the appropriate output button					NOTE	The Adjust	knob and the Adjust		knob
to select the desired output.						are used to adjust the image settings on the
						left and right sides of the LCD screen,
						respectively.

Figure 3-13 — Picture adjustments flowchart

1.Press the desired input button and output button to select an input-output tie to adjust.

The adjustments are made to the input signal as it is switched to the tied output (1 or 2) only. (The output LED is lit and the selected output is shown in the LCD). The adjustments do not affect the same input tied to the other output.

Color adjustments are available only for component video, S-video, and composite video inputs.

Tint adjustments are available only for S-video and composite video inputs.

2.Press the appropriate picture adjustment button: color and tint, brightness and contrast (Brt/Cont), sizing (Size), centering (Center), or filter. The LCD display shows the name of the adjustment and the current setting value.

3-16 Integration Scaling Matrix Switcher • Operation

Image 41

Contents ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Integration Scaling Matrix Switcher Introduction About the SwitcherIntroductiontroduction, cont’d About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Mounting the Switcher Installationstallation, cont’dTabletop placement Rack mountingMounting instructions Mounting the switcherInput connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connectionsOptional output connection Choosing a network cable Cabling and RJ-45 connector wiringWiring the network cable RS-232 connection ConfigurationInstallation, cont’d Three Integration Scaling Matrix Switcher Operation Front Panel Controls and IndicatorsOperationeration, cont’d Video/Audio selection button and LEDsFront panel input label window Output buttons and LEDsInput buttons, LEDs, and label window Black/Mute button and LEDs Picture adjustment buttonsOperation, cont’d Menu control buttons Adjustment knobsLCD display Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuOperation, cont’d 10 Advanced Configuration menu flowchart RGB Delay submenu Blue-Only Mode and Edge Smoothing submenuTest Pattern submenu Blanking submenuPixel Phase submenu Enhanced Mode submenuPAL Film Mode submenu Reset submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustmentsAdjust knobs have no mechanical limits to their rotation Front panel security lockout Executive modeIP information Optimizing the VideoCentering controls to position the image Setting up a DVD sourceGeneral checks TroubleshootingOptimizing the Audio Problem Cause Specific problemsOperation, cont’d Four Ethernet Link Integration Scaling Matrix Switcher Programmer’s GuideRS-232 Link Ethernet connection SymbolsDefault address Power-up Switcher-Initiated MessagesProgrammer’s Guide, cont’d Ties creationX2 Col PAL film mode RGB delayAutomated adjustments Test patternUsing the command/response table Host-to-Switcher InstructionsSwitcher error responses Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’dHorizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commandsCommand/response table for IP SIS commands Command/response table for special function SIS commandsX2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commandsFive Control Software for Windows Installing the softwareIntegration Scaling Matrix Switcher Switcher Software Software operation via Ethernet Ethernet protocol settingsUsing the control program Switcher Software, cont’dWindows Control program window Button-Label Generator Using the help programTo run the Button-Label Generator program, click Start Using the softwareSwitcher Software, cont’d Six Loading the Startup Control Integration Scaling Matrix Switcher Ethernet OperationEthernetOperation,cont’d Control Ethernet Operation, cont’d Changing the RGB delayControl Creating a tieExecutive mode Using Blue-Only modeFreezing the output Outputting a test patternSystem Configuration System ConfigurationISM IP Settings fields Administration fieldsISM IP Address field ISM Name fieldFile Management File ManagementI/O Configuration Input configurationEthernet Operation, cont’d Output rate Output resolutionOutput polarity Output formatSeven Opening and Closing the Switcher Maintenance and ModificationsGrounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’dDVI output card connector opening and socket J14 Installing a DVI Output CardOutput DVI board installation AAppendix a Cabling Integration Scaling Matrix Switcher Ethernet ConnectionEthernet Connection Pinging to determine the Web IP address Determining Default AddressesPinging to determine the switcher’s IP address Ethernet Connection, cont’d Connecting as a Telnet ClientTelnet tips OpenLocal echo Escape character and Esc keySet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb