Extron electronic ISM 482 manual Command/response table for advanced instruction set commands

Page 63

Programmer’s Guide, cont’d

Command/response table for advanced instruction set commands

The advanced instruction set consist of four hexadecimal commands for uploading and downloading all or a portion of the switcher’s memory. These commands are for use by knowledgeable programmers, and result in a dump of data from (upload) or to (download) the switcher. Programmers can use the commands to exactly duplicate the settings among switchers with a minimum of effort.

Command	Hex Command			Response	Additional description
	(host to switcher)			(switcher to host)
Memory backup
Read all memory contents	90 91			{8226 data bytes+1 byte checksum}	Upload (switcher to control
					device) all color, tint, contrast,
					brightness, detail, sizing, and
					centering settings; all user presets;
					and all auto memories for all
					inputs and both outputs.
Write all memory contents	90 92+8226 data bytes+1 byte checksum				Download (control device to
				Dn1	switcher) all color, tint, contrast,
					brightness, detail, sizing, and
					centering settings; all user presets;
					and all auto memories for all
					inputs and both outputs.

Read partial contents		X2	90 93	{26 data bytes+1 byte checksum}	Upload (switcher to control
					device) color, tint, contrast,
					brightness, detail, sizing, and
					centering settings; all user presets;
					and all auto memories for the
					input selected for output	X2	.

Write partial contents			90 94+26 data bytes+1 byte checksum		Download (control device to
Write partial contents		X2	90 94+26 data bytes+1 byte checksum		Download (control device to
				Dn1	switcher) color, tint, contrast,
					brightness, detail, sizing, and

centering settings; all user presets; and all auto memories for the input selected for output X2 .

4-16 Integration Scaling Matrix Switcher • Programmer’s Guide

Image 63

Contents ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’dExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placementMounting instructions Mounting the switcherInstallation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connectionsOptional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable RS-232 connection ConfigurationInstallation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’dOutput buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuOperation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustmentsAdjust knobs have no mechanical limits to their rotation Front panel security lockout Executive modeIP information Optimizing the VideoCentering controls to position the image Setting up a DVD sourceTroubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problemsOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’dX2 Col Test pattern RGB delayPAL film mode Automated adjustmentsHost-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’dHorizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commandsCommand/response table for IP SIS commands Command/response table for special function SIS commandsX2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commandsFive Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Software operation via Ethernet Ethernet protocol settingsUsing the control program Switcher Software, cont’dWindows Control program window Button-Label Generator Using the help programTo run the Button-Label Generator program, click Start Using the softwareSwitcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Creating a tie Changing the RGB delayEthernet Operation, cont’d ControlOutputting a test pattern Using Blue-Only modeExecutive mode Freezing the outputSystem Configuration System ConfigurationISM Name field Administration fieldsISM IP Settings fields ISM IP Address fieldFile Management File ManagementI/O Configuration Input configurationEthernet Operation, cont’d Output rate Output resolutionOutput polarity Output formatSeven Opening and Closing the Switcher Maintenance and ModificationsGrounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’dDVI output card connector opening and socket J14 Installing a DVI Output CardOutput DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tipsClose Escape character and Esc keyLocal echo Set carriage return-line feedEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb