Extron electronic ISM 482 manual Symbols, Ethernet connection, Default address

Page 50

Ethernet connection

The cable can be terminated as either a patch cable or a crossover cable (figure 4-2) and must be properly terminated for your application:

Patch (straight) cable — Connection of the ISM to an Ethernet hub, router, or switcher that also hosts a controlling computer

Crossover cable — Direct connection between the ISM and a computer

Default address

To access the switcher via the Ethernet port, you need the switcher’s IP address. If the address has been changed to an address comprised of words and characters, the actual numeric IP address can be determined using the front panel (see “IP information” in chapter 3, “Operation”) or the Ping utility (see “Ping to determine the switcher’s IP address” or “Ping to determine the Web IP address” in appendix A, “Ethernet Connection”, for more details). If the address has not been changed, the factory-specified default is 192.168.254.254.

Symbols

Symbols ( Xn values), defined below, are used throughout the discussions of the switcher-initiated messages that begins on the next page and the command/ response table that begins on page 4-8. The symbols represent variables in the switcher-initiated messages and the command/response table fields.

= CR/LF (carriage return/line feed) (hex 0D 0A)

= CR (no line feed)

= Space

Esc = Escape key

X1

= Input number (1 through 8)

 

X2

= Output number (1 or 2)

 

 

X3

= 000 = off, 001 = on

 

 

 

X4

= Input video type:

 

 

 

 

000

= RGB

005 = Betacam 60

 

001

= RGBcS

006 = HDTV

 

002

= YUVi

007 = S-video

 

003

= YUVp

008 = Composite

 

004

= Betacam 50

 

 

 

X5

= Scaler resolution:

 

 

 

 

00

= 640x480

09

=

1365x1024

 

01

= 800x600

10

=

720p

 

02

= 832x624

11

=

1080p

 

03

= 848x480

12

=

1080i

 

04

= 852x480

13

=

1400 x 1050

 

05

= 1024x768

14

=

576p

 

06

= 1280x768

15

=

1366x768

 

07

= 1280x1024

16

=

1365x768

 

08

= 1360x765

 

 

 

X6

= Video refresh rate:

 

 

 

 

000

= 50 Hz

003 =

75 Hz

 

001

= 56 Hz

004 =

85 Hz

 

002

= 60 Hz

005 =

AFL*

Lock or AFL is Accu-RATE Frame Lock(PAL = 50 Hz, NTSC = 59.94 Hz)

X7

= Output video type:

00 = RGBHV, 01 = RGBS

X8

= Output sync polarity:

 

 

 

00

= H–/V–

02

= H+/V–

 

01

= H–/V+

03

= H+/V+

X9

= Color value (0 thru 127)

 

X10 = Tint value (0 thru 255)

X11

= Brightness and contrast value (000 thru 63)

 

= Size value (range depends on the resolution)

X12

 

= Centering value (range depends on the resolution)

X13

 

= Blanking value (000 thru 200)

X14

 

= Pixel sampling phase (000 through 031)

X15

 

= Horizontal filter value (000 thru 003)

X16

 

= Vertical filter or composite/S-video detail filter (001 thru 007)

X17

 

= Preset number (01 thru 03)

X18

 

= Output 1/ Output 2 selection:

X19

 

Output 1/Output 2

Output 1/Output 2

 

00 = Off/Off

02 = Off/On

 

01 = On/Off

03 = On/On

 

= RGB delay in 0.01 second steps (00 [no delay] to 50 [5.0 secs])

X20

 

= Test pattern type (001 through 010):

X21

 

001 = Color Bars

006

= alternating pixels

 

002 = crosshatch

007

= film aspect ratio 1.78

 

003 = 4x4 crosshatch

008

= film aspect ratio 1.85

 

004 = gray scale

009

= film aspect ration 2.35

 

005 = crop

010

= ramp

 

= Gain/attenuation (–24dB to +9dB, each step = 1 dB)

X22

 

= Gain value (numeric dB value, 0 to +9)

X23

 

= Attenuation value (numeric dB value, –1 to –24)

X24

 

= nnn.nn, where

 

 

X25

 

 

 

Hrt = horizontal rate (kHz)

 

 

Vrt = vertical rate (Hz)

 

 

 

xxx:xx means signal out of range

 

= Detected input signal standard (0 through 4):

X26

0 = none

1 = NTSC 3.58

2 = PAL

3 = NTSC 4.43

4 = SECAM

= not applicable (occurs when the input is set for RGB, YUV, or progressive YUV)

Integration Scaling Matrix Switcher • Programmer’s Guide

4-3

Image 50
Contents ISM Precautions FCC Class B Notice Quick Start Integration Scaling Matrix Switcher Integration Scaling Matrix Switcher Quick Start QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Integration Scaling Matrix Switcher Quick StartTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Rack mountingMounting the switcher Mounting instructionsInput connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs videoOptional output connection Choosing a network cable Cabling and RJ-45 connector wiringWiring the network cable Configuration RS-232 connectionInstallation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsFront panel input label window Output buttons and LEDsInput buttons, LEDs, and label window Black/Mute button and LEDs Picture adjustment buttonsOperation, cont’d Menu control buttons Adjustment knobsLCD display Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuOperation, cont’d 10 Advanced Configuration menu flowchart Test Pattern submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Centering controls to position the imageGeneral checks TroubleshootingOptimizing the Audio Specific problems Problem CauseOperation, cont’d Four Ethernet Link Integration Scaling Matrix Switcher Programmer’s GuideRS-232 Link Ethernet connection SymbolsDefault address Programmer’s Guide, cont’d Switcher-Initiated MessagesPower-up Ties creationX2 Col Automated adjustments RGB delayPAL film mode Test patternUsing the command/response table Host-to-Switcher InstructionsSwitcher error responses Programmer’s Guide, cont’d Command/response table for SIS commands cont’d Command Ascii Command Response Additional descriptionHorizontal detail filter RGB and component video inputs User presets Verbose mode Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Command/response table for IP SIS commandsX2 Reconfig message may not be Command/response table for advanced instruction set commands Command Hex Command ResponseFive Control Software for Windows Installing the softwareIntegration Scaling Matrix Switcher Switcher Software Ethernet protocol settings Software operation via EthernetSwitcher Software, cont’d Using the control programWindows Control program window Using the help program Button-Label GeneratorUsing the software To run the Button-Label Generator program, click StartSwitcher Software, cont’d Six Loading the Startup Control Integration Scaling Matrix Switcher Ethernet OperationEthernetOperation,cont’d Control Control Changing the RGB delayEthernet Operation, cont’d Creating a tieFreezing the output Using Blue-Only modeExecutive mode Outputting a test patternSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationEthernet Operation, cont’d Output resolution Output rateOutput format Output polaritySeven Maintenance and Modifications Opening and Closing the SwitcherGrounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware UpgradeInstalling a DVI Output Card DVI output card connector opening and socket J14Output DVI board installation AAppendix a Cabling Integration Scaling Matrix Switcher Ethernet ConnectionEthernet Connection Pinging to determine the Web IP address Determining Default AddressesPinging to determine the switcher’s IP address Telnet tips Connecting as a Telnet ClientEthernet Connection, cont’d OpenSet carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 82 pages 3.94 Kb