Extron electronic ISM 482 manual Front panel security lockout Executive mode

Page 42

3.Rotate the Adjust knob or Adjust knob to vary the settings within the following adjustment ranges:

The Adjust knobs have no mechanical limits to their rotation.

•Color/Tint: Color adjusts within a range of 0 to 127. Tint adjusts within a range of 0 to 255.

•Brightness/Contrast: The range for both adjustments is 0 to 63.

•Size: Observe the display and turn the Adjust knob to increase or decrease the horizontal size of the image. Turn the Adjust knob to increase or decrease the vertical size of the image. The adjustment range depends on the input rate applied and the selected output resolution.

•Center: Observe the display and turn the Adjust knob to center the image horizontally or the Adjust knob to center the image vertically. The adjustment range depends on the input rate applied and the selected output resolution.

•Horizontal and vertical filter (RGB or component video input): Horizontal (Horz) adjusts within a range of 0 to 3.

Vertical (Vert) adjusts within a range of 0 to 7.

•Filter (S-video and composite video input): Either knob adjusts within a range of 0 to 7.

4.Repeat steps 2 and 3 for each image adjustment to be made for that output.

5.

If you want to set picture adjustment on the another tie, press the another

 

input button or the other output button.

Front panel security lockout (Executive mode)

The front panel security lockout limits the operation of the Integration Scaling Matrix switcher from the front panel. When the switcher’s front panel is locked, all of the front panel functions are disabled except for input and output selection and black/mute selection.

To toggle the front panel lock on and off, press and hold the Color/Tint and Center buttons for approximately 2 seconds (figure 3-14). The LCD displays Executive Mode Enabled or Executive Mode Disabled to indicate the mode. Release the buttons. The LCD also displays Executive Mode Enabled if you push a locked out button when the switcher’s front panel is locked.

Default

Cycle

Press and hold both buttons simultaneously for 2 seconds

COLOR/

 

 

CENTER

TINT

 

 

 

ISM 482

 

 

ISM 482

 

 

Executive Mode

OR

Executive Mode

Enabled

 

 

Disabled

10sec. timeout

Figure 3-14 — Front panel security lockout flowchart

Integration Scaling Matrix Switcher • Operation 3-17

Page 41 Page 43
Image 42
Page 41 Page 43
Contents ISM Precautions FCC Class B Notice Quick Start Integration Scaling Matrix Switcher Integration Scaling Matrix Switcher Quick Start QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Integration Scaling Matrix Switcher Quick StartTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Rack mountingMounting the switcher Mounting instructionsInstallation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs videoOptional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable Configuration RS-232 connectionInstallation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsOutput buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuOperation, cont’d 10 Advanced Configuration menu flowchart Test Pattern submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Centering controls to position the imageTroubleshooting Optimizing the AudioGeneral checks Specific problems Problem CauseOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Programmer’s Guide, cont’d Switcher-Initiated MessagesPower-up Ties creationX2 Col Automated adjustments RGB delayPAL film mode Test patternHost-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command/response table for SIS commands cont’d Command Ascii Command Response Additional descriptionHorizontal detail filter RGB and component video inputs User presets Verbose mode Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Command/response table for IP SIS commandsX2 Reconfig message may not be Command/response table for advanced instruction set commands Command Hex Command ResponseFive Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Ethernet protocol settings Software operation via EthernetSwitcher Software, cont’d Using the control programWindows Control program window Using the help program Button-Label GeneratorUsing the software To run the Button-Label Generator program, click StartSwitcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Control Changing the RGB delayEthernet Operation, cont’d Creating a tieFreezing the output Using Blue-Only modeExecutive mode Outputting a test patternSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationEthernet Operation, cont’d Output resolution Output rateOutput format Output polaritySeven Maintenance and Modifications Opening and Closing the SwitcherGrounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware UpgradeInstalling a DVI Output Card DVI output card connector opening and socket J14Output DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Telnet tips Connecting as a Telnet ClientEthernet Connection, cont’d OpenSet carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 82 pages 3.94 Kb
Top Page Image Contents