Extron electronic ISM 482 manual Programmer’s Guide, cont’d, Switcher-Initiated Messages, Power-up

Page 51

Programmer’s Guide, cont’d

Switcher-Initiated Messages

When a local event such as power-up or a front panel operation occurs, the switcher responds by sending a message to the host. The switcher-initiated messages are listed in the following pages. The messages are underlined.

The switcher does not expect a response from the host; but, for example, the host program might request a new status.

Power-up

(c) Copyright 2002, Extron Electronics, ISM 482, Vx.xx

The switcher initiates the copyright message when it is first powered on. Vxxxx is the firmware version number.

Ties creation

Out X2 •In X1 •All

A front panel video and audio switching operation has occurred. X2 is the output number and X1 is the input number.

Out X2 •In X1 •RGB

A front panel video-only switching operation has occurred. X2 is the output number and X1 is the input number.

Out X2 •In X1 •Aud

A front panel audio-only switching operation has occurred. X2 is the output number and X1 is the input number.

Input and output video type

X1 Typ X4

A front panel input video type selection has occurred. X4 is the input video type.

X2 Rte X5X6

X1

is the input number and

A front panel output video format selection has occurred. X2 is the output number, X5 is the output resolution, and X6 is the output refresh rate.

X2 Syn X7

A front panel output video type selection has occurred. X2 is the output number and X7 is the output video format (RGBHV or RGBS).

X2 Pol X8

A front panel output video polarity selection has occurred. X2 is the output number and X8 is the output sync polarity.

4-4 Integration Scaling Matrix Switcher • Programmer’s Guide

Image 51

Contents ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’dExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placementMounting instructions Mounting the switcherInstallation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connectionsOptional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable RS-232 connection ConfigurationInstallation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’dOutput buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuOperation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustmentsAdjust knobs have no mechanical limits to their rotation Front panel security lockout Executive modeIP information Optimizing the VideoCentering controls to position the image Setting up a DVD sourceTroubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problemsOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’dX2 Col Test pattern RGB delayPAL film mode Automated adjustmentsHost-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’dHorizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commandsCommand/response table for IP SIS commands Command/response table for special function SIS commandsX2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commandsFive Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Software operation via Ethernet Ethernet protocol settingsUsing the control program Switcher Software, cont’dWindows Control program window Button-Label Generator Using the help programTo run the Button-Label Generator program, click Start Using the softwareSwitcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Creating a tie Changing the RGB delayEthernet Operation, cont’d ControlOutputting a test pattern Using Blue-Only modeExecutive mode Freezing the outputSystem Configuration System ConfigurationISM Name field Administration fieldsISM IP Settings fields ISM IP Address fieldFile Management File ManagementI/O Configuration Input configurationEthernet Operation, cont’d Output rate Output resolutionOutput polarity Output formatSeven Opening and Closing the Switcher Maintenance and ModificationsGrounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’dDVI output card connector opening and socket J14 Installing a DVI Output CardOutput DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tipsClose Escape character and Esc keyLocal echo Set carriage return-line feedEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb