Extron electronic ISM 482 manual Switcher Software, cont’d, Using the control program

Page 67

Switcher Software, cont’d

Using the control program

Many items found in the ISS/ISM Control Program are also accessible via front panel controls and the LCD menus (see chapter 3, “Operation”) and under SIS control (see chapter 4, “Programmer’s Guide”). The ISS/ISM Help Program provides information on settings and on how to use the control program, itself.

1. To run the control program, click Start > Programs > Extron Electronics > ISSISM. The Comm menu appears on the screen (figure 5-3).

Figure 5-3 — Comm Port Selection window

2. Select the comm port that is connected to the ISM’s Remote port or select IP [LAN] and click OK.

If you selected a comm port, proceed to step 5.

If you selected IP [LAN], proceed to step 3.

3. If you selected IP [LAN] in step 2, the IP connection window appears (figure 5-4). The window displays the last IP address that this computer was logged on to via the ISS/ISM Control Program. If no one has logged on to the ISM from this computer, enter the ISM IP address. If the address has not been changed, the factory-specified default is 192.168.254.254.

Figure 5-4 — Address and password entry

4. If you selected IP [LAN] in step 2, when prompted, enter the appropriate administrator or user password and click Connect.

If you logged on using the administrator password, the program connects you to the ISM with all of the administrator rights and privileges.

If you logged on using the user password, the program connects you to the

ISM with only user capabilities.

If an incorrect password was entered, the program beeps and returns to the password entry display.

5-4 Integration Scaling Matrix Switcher • Switcher Software

Image 67

Contents ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’dExtron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placementMounting instructions Mounting the switcherCabling and Rear Panel Views Installation, cont’dInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connectionsOptional output connection Wiring the network cable Cabling and RJ-45 connector wiringChoosing a network cable RS-232 connection ConfigurationInstallation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’dInput buttons, LEDs, and label window Output buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuOperation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustmentsAdjust knobs have no mechanical limits to their rotation Front panel security lockout Executive modeIP information Optimizing the VideoCentering controls to position the image Setting up a DVD sourceOptimizing the Audio TroubleshootingGeneral checks Problem Cause Specific problemsOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Default address SymbolsEthernet connection Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’dX2 Col Test pattern RGB delayPAL film mode Automated adjustmentsSwitcher error responses Host-to-Switcher InstructionsUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’dHorizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commandsCommand/response table for IP SIS commands Command/response table for special function SIS commandsX2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commandsFive Integration Scaling Matrix Switcher Switcher Software Installing the softwareControl Software for Windows Software operation via Ethernet Ethernet protocol settingsUsing the control program Switcher Software, cont’dWindows Control program window Button-Label Generator Using the help programTo run the Button-Label Generator program, click Start Using the softwareSwitcher Software, cont’d Six EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoading the Startup Control Control Creating a tie Changing the RGB delayEthernet Operation, cont’d ControlOutputting a test pattern Using Blue-Only modeExecutive mode Freezing the outputSystem Configuration System ConfigurationISM Name field Administration fieldsISM IP Settings fields ISM IP Address fieldFile Management File ManagementI/O Configuration Input configurationEthernet Operation, cont’d Output rate Output resolutionOutput polarity Output formatSeven Opening and Closing the Switcher Maintenance and ModificationsGrounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’dDVI output card connector opening and socket J14 Installing a DVI Output CardOutput DVI board installation AAppendix a Ethernet Connection Integration Scaling Matrix Switcher Ethernet ConnectionCabling Pinging to determine the switcher’s IP address Determining Default AddressesPinging to determine the Web IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tipsClose Escape character and Esc keyLocal echo Set carriage return-line feedEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 82 pages 3.94 Kb