Extron electronic IPI 200 Series, IPI 100 Series manual  Zy

Page 90

5-32 IPI 100 Series, IPI 200 Series • Programming and Control

Command

ASCII (Telnet)

URL Encoded (Web)

Response

Additional

 

(host to intercom)

(host to intercom)

(intercom to host)

description

 

 

 

 

 

Reset all device

E ZY}

WZY

Zpy]

 

settings and

 

 

 

 

delete files

 

 

 

 

NThis is an absolute system reset but excludes IP settings such as IP address, subnet mask, gateway IP address, unit name, DHCP setting and port mapping (Telnet/Web/direct access) in order to preserve communicaiton with the device. This reset is recommended after a firmware update.

NThe ZY command appears n kernel versions 1.45 or higher.

Absolute system E ZQQQ}

WZQQQ

Zpq]

reset

 

 

N(Mode 5 reset) Resets alls device settings, including IP settings, to factory default. Also rerases flash memory. Firmware version remains the same.

IPI 201/204 SIS™ Programming, cont’d

Page 89 Page 91
Image 90
Page 89 Page 91
Contents User’s Manual MediaLink IP Intercom InterfacesPrecautions 安全须知 中文 This page has been intentionally left blank Quick Start Guide IPI 101, IPI IPI 100 Series, IPI 200 Series Quick Start Guide QS-1Quick Start Guide -­ IPI 101, IPI 104, cont’d QS-2 IPI 100 Series, IPI 200 Series Quick Start GuideQuick Start Guide IPI 201, IPI IPI 100 Series, IPI 200 Series Quick Start Guide QS-3This page has been intentionally left blank Table of Contents Table of Contents, cont’d One Terms used in this manual About this ManualAbout the IP Intercom Modules Additional reference materialIPI 100 Series, IPI 200 Series Introduction Introduction, cont’d Features System RequirementsTwo Installing or Replacing Button Labels IPI 100 Series, IPI 200 Series InstallationUL Requirements IPI 100 Series, IPI 200 Series Installation IPI 100 AAP, IPI 200 AAP Series Installation MLC 226 IP AAPIPI 100 AAP, IPI 200 AAP Series Installation Installation, cont’d IPI Rear Panel Features and Cabling IPI 104 AAP, IPI 101 AAP Rear PanelAAP mounting screws These four screws are permanently MLC Audio Connection Installation, cont’dSingle PC-to-panel mode Sample ApplicationsMultiple PC-to-panel mode Intercom user releases the button when done speakingInstallation, cont’d Panel-to-panel mode Intercom with amplifier mode TCP/IPMLC 226 IP Installation, cont’d Three High MED LOW Button Operation Push to talk operationIPI 100 Series, IPI 200 Series Operation Button Color Indication Operation, cont’dIndication lighting PI 100 AAP, IPI 200 AAP Series OperationFour Installing the Software IPI 100 Series, IPI 200 Series Configuration and ControlSoftware System Requirements Using the Software an Overview Configuration and Control, cont’d IP Intercom HelpDesk screen before configurationParts of the Main Screen Speaking to an intercom Making a group announcementIPI 100 Series, IPI 200 Series Configuration and Control Listening to an intercom Click the Play to Intercoms buttonHands-free operation No Incoming Calls is displayed when no calls are coming Select Advanced Settings... from the Intercom menu Main Screen Menus File menuTools menu Intercom menu Help menuSetting preferences General OptionsPush to Talk PTT Options These settings affect Configuring the IPI Intercom System Startup Audio These controls affect what, if any, soundParts of the Configuration Utility screen Configuration Utility menus Tools menu Upload the Station Not Present Wave File to Intercom Setup procedure IPI 100 Series, IPI 200 Series Configuration and Control Configuration and Control, cont’d Recording an original message Changing the audio format of existing files IPI 100 Series, IPI 200 Series Configuration and Control Configuration and Control, cont’d Chapter Five IPI-initiated Messages IPI 201/204 SIS Programming and ControlHost-to-IPI Communications IPI 100 Series, IPI 200 Series SIS Programming and ControlPassword information Error responsesUsing the command/response tables Commands and ReponsesError response references IPI 201/204 SIS Programming, cont’dIPI 100 Series, IPI 200 Series Programming and Control Symbol definitions X1#= Local date and time format= off/ignore This could be as large as 10 digits Description Command Ascii Telnet URL Encoded Web Response AdditionalX20 Programming and ControlStatus commands +X20X1!  ControlIPI 201/IPI 201/IPI 204 -Thu, 20 Jan 2005 IPI 100 Series, IPI 200 Series Cont’d IPI 201/204 SIS ProgrammingIpnX4   X1@ CN Ipn X1@  CN X1@ or X4  X1# CT Ipt X1#  X1#  X# CZ  X3$ CX X3$ X1$ CI  X1 CS X1$ X1* or  X1$ CG X2@ CV X2@Bmd X6$,X1$  X2@  X6$,X1$ EB   X6$ EB WCC  X3# CA  CK  X4!  X3# CU  IpuX4!  X5@ orRemapping port designations Directory commands IPI 201/204 SIS Programming, cont’dSeries, IPI 200 Series Programming and Control Stream Files via Telnet or RS-232 File handling commands Stream Files via Port DF Evt Tue, 01 Mar 2005 020307 GMT  1AE  0AE ZY AAppendix a Audio input IPI IPI 100 Series, IPI 200 Series Specifications, AccessoriesAudio IPI 101, IPI 104, and MLC 226 IP Audio outputGeneral Audio Audio inputControl relay Specifications, Part Numbers, Accessories, cont’d Included Parts IPI 101 AAP and IPI 104 AAP AccessoriesIncluded parts Replacement Part number MediaLink Controllers, labels Part numberAmplifiers, cable, miscellany Part number Extron’s Warranty USA, Canada, South America Japan Central AmericaExtron Electronics. All rights reserved
Top Page Image Contents