Extron electronic IPI 200 Series, IPI 100 Series manual Audio input

Page 94

Specifications, Part Numbers, Accessories, cont’d

Specifications — IPI 201 and IPI 204 Series

Audio

Speaker	1.4” (35.6 mm), 1-way, indoor
Frequency response
Line level output	20 Hz to 3.3 kHz, ±1 dB
Speaker output	300 Hz to 3.3 kHz, -10 dB
Nominal sensitivity/IPI speaker output level
	80 dB SPL, 300 mW, 3' (1 m)
Processing
Audio format	PCM, µ-law companded
Sampling rate	8 kHz
Sample size	16 bit, µ-law companded to 8 bit
Audio latency	<100 ms
Audio input
Number/signal type	1 mono, via integrated electret microphone
Microphone gain	-30 dB to 0 dB, adjustable in 2 dB steps

N0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

Audio output

Number/signal type	2 mono: 1 via audio output port, 1 via IPI
	speaker
Line level (MLC)	-10 dBV (316 mVrms), balanced/
	unbalanced (via 3.5 mm captive screw
	connector, 2 pole)
Amplified speaker IPI	300 mW, continuous, 1% THD

Ethernet control interface

Ethernet control communications port

1 RJ-45 female connector

Ethernet data rate/transport bandwidth 80 kbps

Communications type	Half duplex
Ethernet protocol	TCP/IP (control), UDP (port 3121, audio),
	Telnet
Default settings	Link speed and duplex level: autodetected
	IP address = 192.168.254.254
	Subnet mask = 255.255.0.0
	Default gateway = 0.0.0.0
	DHCP = off

A-4 IPI 100 Series, IPI 200 Series • Specifications, Accessories

Image 94

Contents User’s Manual MediaLink IP Intercom InterfacesPrecautions 安全须知中文 This page has been intentionally left blank Quick Start Guide IPI 101, IPI IPI 100 Series, IPI 200 Series Quick Start Guide QS-1Quick Start Guide - IPI 101, IPI 104, cont’d QS-2 IPI 100 Series, IPI 200 Series Quick Start GuideQuick Start Guide IPI 201, IPI IPI 100 Series, IPI 200 Series Quick Start Guide QS-3This page has been intentionally left blank Table of Contents Table of Contents, cont’d One Terms used in this manual About this ManualAbout the IP Intercom Modules Additional reference materialIPI 100 Series, IPI 200 Series Introduction Introduction, cont’d Features System RequirementsTwo IPI 100 Series, IPI 200 Series Installation Installing or Replacing Button LabelsUL Requirements IPI 100 Series, IPI 200 Series Installation IPI 100 AAP, IPI 200 AAP Series Installation MLC 226 IP AAPIPI 100 AAP, IPI 200 AAP Series Installation Installation, cont’d IPI Rear Panel Features and Cabling IPI 104 AAP, IPI 101 AAP Rear PanelAAP mounting screws These four screws are permanently MLC Audio Connection Installation, cont’dSingle PC-to-panel mode Sample ApplicationsMultiple PC-to-panel mode Intercom user releases the button when done speakingInstallation, cont’d Panel-to-panel mode Intercom with amplifier mode TCP/IPMLC 226 IP Installation, cont’d Three High MED LOW Push to talk operation Button OperationIPI 100 Series, IPI 200 Series Operation Button Color Indication Operation, cont’dIndication lighting PI 100 AAP, IPI 200 AAP Series OperationFour IPI 100 Series, IPI 200 Series Configuration and Control Installing the SoftwareSoftware System Requirements Using the Software an Overview Configuration and Control, cont’d IP Intercom HelpDesk screen before configurationParts of the Main Screen Speaking to an intercom Making a group announcementIPI 100 Series, IPI 200 Series Configuration and Control Listening to an intercom Click the Play to Intercoms buttonHands-free operation No Incoming Calls is displayed when no calls are coming Select Advanced Settings... from the Intercom menu File menu Main Screen MenusTools menu Intercom menu Help menuSetting preferences General OptionsPush to Talk PTT Options These settings affect Configuring the IPI Intercom System Startup Audio These controls affect what, if any, soundParts of the Configuration Utility screen Configuration Utility menus Tools menu Upload the Station Not Present Wave File to Intercom Setup procedure IPI 100 Series, IPI 200 Series Configuration and Control Configuration and Control, cont’d Recording an original message Changing the audio format of existing files IPI 100 Series, IPI 200 Series Configuration and Control Configuration and Control, cont’d Chapter Five IPI-initiated Messages IPI 201/204 SIS Programming and ControlHost-to-IPI Communications IPI 100 Series, IPI 200 Series SIS Programming and ControlPassword information Error responsesUsing the command/response tables Commands and ReponsesError response references IPI 201/204 SIS Programming, cont’dIPI 100 Series, IPI 200 Series Programming and Control Symbol definitions X1#= Local date and time format= off/ignore This could be as large as 10 digits Description Command Ascii Telnet URL Encoded Web Response AdditionalX20 Programming and ControlStatus commands +X20X1! ControlIPI 201/IPI 201/IPI 204 -Thu, 20 Jan 2005 IPI 100 Series, IPI 200 Series Cont’d IPI 201/204 SIS ProgrammingIpnX4 X1@ CN Ipn X1@ CN X1@ or X4 X1# X1# CT Ipt X1# X# CZ X3$ X3$ CX X1$ CI X1 CS X1$ X1* or X1$ CG X2@ CV X2@Bmd X6$,X1$ X2@ X6$,X1$ EB X6$ EB WCC X3# CA CK X4! X3# CU IpuX4! X5@ orRemapping port designations Directory commands SIS Programming, cont’d IPI 201/204Series, IPI 200 Series Programming and Control Stream Files via Telnet or RS-232 File handling commands Stream Files via Port DF Evt Tue, 01 Mar 2005 020307 GMT 1AE 0AE ZY AAppendix a Audio input IPI IPI 100 Series, IPI 200 Series Specifications, AccessoriesAudio IPI 101, IPI 104, and MLC 226 IP Audio outputGeneral Audio Audio inputControl relay Specifications, Part Numbers, Accessories, cont’d Included Parts IPI 101 AAP and IPI 104 AAP AccessoriesIncluded parts Replacement Part number MediaLink Controllers, labels Part numberAmplifiers, cable, miscellany Part number Extron’s Warranty USA, Canada, South America Japan Central AmericaExtron Electronics. All rights reserved