Extron electronic manual Connecting the MSG0804 and MSG0808, MSG0808 installation example

Page 15

Connecting the MSG0804 and MSG0808

The MSG Matrix Switchers can be connected to as many as 8 input devices simultaneously and output up to four (MSG0804) or eight (MSG0808) simultaneously. Follow the steps below and see the installation example in figure 2-4.

1

2

3

4

5

If the MSG Matrix Switcher is to be mounted, see Mounting the Switcher, earlier in this chapter.

Turn off power to the switcher and all other devices that will be connected.

Using the BNC input connectors, attach up to eight RGBHV video input devices to the switcher.

Connect up to four output devices to the MSG0804, or eight output devices to the MSG0808 using the output BNC connectors.

For stereo audio input, connect up to eight audio sources to the switcher using 5 mm, 5-pole captive screw connectors. See the following Audio input and output section. Connect audio output to the switcher using 5 mm, 5-pole captive screw connectors.

Extron

CTL208

Control Module

Sound

System

Extron

MSG0808HR

Matrix Switcher

Extron

 

Monitor

DAS101CM

 

 

Audio Buffer

 

Projector

 

 

Extron

 

 

DAV101CM-3

 

Extron

Line Driver

Extron

Laptop

IN1404

CIA116

Video Scaler

 

Interface

 

 

PC

 

DVD

 

 

Figure 2-4— MSG0808 installation example

6

7

If the switcher is to be connected to a computer or host controller for remote control, connect the host’s RS-232 cable to the 5-pole captive screw serial port of the switcher. For an RS-232/RS-422/RS-485 pinout table and dip switch settings, see the related information on page 2-4.

Power up the input and output devices, then connect power to the switcher.

MSG Matrix Switchers • Installation

2-5

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MSG0804 and MSG0808 Matrix SwitchersSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisConnecting the MSG0808 Quick Start MSG0804 and MSG0808Rack mounting the MSG0808 Operation Quick Start MSG0804 and MSG0808, cont’dTable of Contents Table of Contents, cont’d Introduction OneIntroduction About the MSG Matrix SwitchersMSG Matrix Switcher Features MSG Matrix Switchers IntroductionFlexible Control Options This page intentionally left blank Two InstallationTabletop use InstallationMounting the Switcher MSG Matrix Switchers InstallationVideo Inputs Video Outputs Rear Panel ConnectorsRS-485 Half Duplex Connection Installation, cont’dMSG0808 installation example Connecting the MSG0804 and MSG0808Balanced audio Installation, cont’dAudio input and output Unbalanced audioConnecting the external sync signal Vertical Interval SwitchingThis page intentionally left blank Operation ThreeFront Panel Features MSG Matrix Switchers OperationOperation Miscellaneous front panel functions Connecting inputs with outputsPreset configurations Front Panel OperationSelecting the switching level audio versions only Reset to factory defaultOperation, cont’d Windows-based Control Program FourInstalling the Windows-based ICS100 Control Software Using the SoftwareWindows-based Control Program, Cont’d ICS100 Interface screen MSG switcher controls options Using the control panelCreating a new patch Setting volume levelsAdjusting output volume levels Defining input icons and labelsICS100 Set Output Volume window Adjusting input volume levelsOpening the Options menu Setting and using presetsResetting the unit VIS EnableEnable Response Using Terminal CommThis page intentionally left blank Five Remote ControlRemote Control Dip Switch SettingsMSG Matrix Switchers Remote Control Host-to-MSG Matrix Switcher Communications Addressing commandsUsing the command table Command Description Remote Control, cont’dCommand Table Set-up commandsBlank output Switching commandsVolume commands Switching levels audio models onlyMute all outputs Stop volume ramp Change input volume level global Remote Control from a NetworkPreset commands Enabling remote control of the switcher over a networkICS100 Serial Port Server window Instructions for configuring the client remote PCStopping communications from the server PC Adjusting response timeAdjusting the response time Stopping communicationPress this button first CTL120-2 IR Remote ControlRemote Control, cont’d AAppendix SpecificationsVideo output SpecificationsVideo Video inputAudio input MSG Matrix Switchers Specifications A-3Sync Audio audio models onlyGeneral Specifications MSG0804 and MSG0808Control/remote switcher MSG Matrix Switchers SpecificationsReference Information BAppendixTo update the firmware Reference InformationUpdating the Firmware Installing Custom Engraved Nameplates Installing the custom nameplatesMSG Matrix Switchers Reference Information Part Numbers MSG Matrix Switcher part numbersOptional accessories Reference Information, cont’dExtron Part BNC-4 Mini HR Cable Plenum Seventeen Conductor Installation CableAssorted connectors BNC connectors Pre-cut cablesThis page intentionally left blank FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents