Extron electronic MSG0804, MSG0808 manual CTL120-2 IR Remote Control, Press this button first

Page 41

CTL120-2 IR Remote Control

The CTL120-2 IR Remote Control sends infrared commands to the built-in infrared receiver in the MSG switchers to control various switcher functions. The illustration below shows the location and function of each button on the Remote Control unit that can be used to control the MSG matrix switchers.

Initially, press the Matrix button on the Remote Control unit to change it to matrix switcher mode.

To switch to a new input/output configuration using the CTL120-2 Remote Control:

1.Press the button on the remote control unit that corresponds to the desired output select button.

2.Press the button on the remote control unit that corresponds to the desired input that you want to connect to the output.

3.Press the Enter button to confirm the configuration.

MATRIX

Matrix Button Press this button first to set the CTL120-2

to control the MSG0804 or MSG0808 matrix switchers

Important!

Press this button first!

S

VIDEO
SCALER SWITCHER	MATRIX	AUDIO

Numeric Buttons

Press to select desired output, then to select desired input

Press the Enter button to confirm the configuration

1 2 3

4 5 6

7 8 9

	0	ENTER
PIP	0	ENT
INPUT		RECALL

FREEZE

	MENU		OK
MENU	CH VOL		ENTER

+		+
–		–

"0" Button Press to blank the currently selected input

Enter Button

Press to make menu selection, or to execute a new setting when using on-screen commands

Volume Buttons

Press (+) to increase volume, or (-) to decrease volume

BLANKMUTE

Mute Button

Press to mute audio

Figure 5-3 — CTL120-2 Infrared Remote Control

MSG Matrix Switchers • Remote Control 5-11

Image 41

Contents MSG0804 and MSG0808 Matrix SwitchersSafety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschRack mounting the MSG0808 Connecting the MSG0808Quick Start MSG0804 and MSG0808 Operation Quick Start MSG0804 and MSG0808, cont’dTable of Contents Table of Contents, cont’d Introduction OneMSG Matrix Switcher Features About the MSG Matrix SwitchersMSG Matrix Switchers Introduction IntroductionFlexible Control Options This page intentionally left blank Two InstallationMounting the Switcher InstallationMSG Matrix Switchers Installation Tabletop useVideo Inputs Video Outputs Rear Panel ConnectorsRS-485 Half Duplex Connection Installation, cont’dMSG0808 installation example Connecting the MSG0804 and MSG0808Audio input and output Installation, cont’dUnbalanced audio Balanced audioConnecting the external sync signal Vertical Interval SwitchingThis page intentionally left blank Operation ThreeOperation Front Panel FeaturesMSG Matrix Switchers Operation Preset configurations Connecting inputs with outputsFront Panel Operation Miscellaneous front panel functionsOperation, cont’d Selecting the switching level audio versions onlyReset to factory default Windows-based Control Program FourWindows-based Control Program, Cont’d Installing the Windows-based ICS100 Control SoftwareUsing the Software ICS100 Interface screen MSG switcher controls options Using the control panelAdjusting output volume levels Setting volume levelsDefining input icons and labels Creating a new patchICS100 Set Output Volume window Adjusting input volume levelsOpening the Options menu Setting and using presetsEnable Response VIS EnableUsing Terminal Comm Resetting the unitThis page intentionally left blank Five Remote ControlMSG Matrix Switchers Remote Control Remote ControlDip Switch Settings Using the command table Host-to-MSG Matrix Switcher CommunicationsAddressing commands Command Table Remote Control, cont’dSet-up commands Command DescriptionVolume commands Switching commandsSwitching levels audio models only Blank outputMute all outputs Stop volume ramp Preset commands Remote Control from a NetworkEnabling remote control of the switcher over a network Change input volume level globalICS100 Serial Port Server window Instructions for configuring the client remote PCAdjusting the response time Adjusting response timeStopping communication Stopping communications from the server PCPress this button first CTL120-2 IR Remote ControlRemote Control, cont’d AAppendix SpecificationsVideo SpecificationsVideo input Video outputSync MSG Matrix Switchers Specifications A-3Audio audio models only Audio inputControl/remote switcher Specifications MSG0804 and MSG0808MSG Matrix Switchers Specifications GeneralReference Information BAppendixUpdating the Firmware To update the firmwareReference Information MSG Matrix Switchers Reference Information Installing Custom Engraved NameplatesInstalling the custom nameplates Optional accessories MSG Matrix Switcher part numbersReference Information, cont’d Part NumbersAssorted connectors BNC connectors Plenum Seventeen Conductor Installation CablePre-cut cables Extron Part BNC-4 Mini HR CableThis page intentionally left blank FCC Class a Notice Extron’s Warranty Extron Electronics, USA