Extron electronic 124, 84, 1616, 1212, 168, 816, 88 manual Definitions, Extron CrossPoint 300 128 HVA

Page 11

Classroom 101 Classroom 102

Extron

CrossPoint 300 128 HVA

Matrix Switcher

8 Outputs

Extron

DVS 304

Scaler

Extron

VSC 700

Scan Converter

DVD

Extron

DVS 304

Scaler

12 Inputs

VCR

Extron

RGB 109xi

Interface

Cable Box	Extron
	DVS 304
	Scaler
	CD Player	Student	Instructor
		Computer	Computer

Figure 1-1 — Typical CrossPoint matrix switcher application

Definitions

The following terms, which apply to Extron matrix switchers, are used throughout this manual:

Tie — An input-to-output connection.

Set of ties — An input tied to two or more outputs. (An output can never be tied to more than one input.)

Configuration — One or more ties or one or more sets of ties.

Current configuration — The configuration that is currently active in the switcher (also called configuration 0)

Global memory preset — A configuration that has been stored. Up to 32 global memory presets can be stored in memory. Preset locations are assigned to the input buttons and output buttons. Up to 20 or 32 (depending on the number of input and output buttons) presets can be selected from the front panel for either saving or retrieving. When a preset is retrieved from memory, it becomes the current configuration. All models have 32 presets; on models with fewer than 32 input and output buttons, preset numbers that are too high to be available from the front panel are accessible via serial port control.

CrossPoint 300 Matrix Switchers • Introduction

1-3

Image 11

Contents CrossPoint 300 Series Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschCrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix SwitchersQS-2 CrossPoint 300 Matrix Switchers Quick Start Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset View, adjust the audio levelTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About this Manual About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction Introductiontroduction, cont’dExtron CrossPoint 300 128 HVA DefinitionsIntroduction, cont’d FeaturesCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two UL requirements Installationstallation, cont’dMounting the Switcher CrossPoint 300 Matrix Switchers InstallationShows the CrossPoint 300 128 HVA Connections and Rear Panel FeaturesAudio input and output HVA models only Installation, cont’dRgbhv input and output Typical audio connectors Remote RS-232/RS-422 port Reset buttonPower Sync termination switchesFront panel configuration port Front Panel Configuration PortCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint 300 Matrix Switchers Operation Input and output buttons DefinitionsControl buttons Operation, cont’dCrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel OperationsCreating a configuration Power indicationsClear all selections Example 1 Creating a set of video and audio tiesExample 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio29 Select Rgbhv and audio 31 Unmute the outputs Using global presetsLED blinks figure Example 6 Saving a presetPress and release the Preset button figure Example 7 Recalling a preset39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models42 Clear all selections Example 8 Viewing and adjusting an input audio levelAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA modelsReading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volumeAudio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and modePower Performing a system reset from the front panelSelecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panelPerforming a hard reset from the rear panel Optimizing the Audio HVA SwitchersGeneral checks TroubleshootingPlasma display S-video problem Worksheet example 1 Entering system equipment Configuration WorksheetsWorksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration66 Worksheet example 3 Test configuration Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetThis page was intentionally left blank Four Rear panel Remote port CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Serial PortsFront panel Configuration port Host-to-Switcher InstructionsProgrammer’s Guide, cont’d Switcher-Initiated MessagesUsing the Command/Response Table Switcher Error ResponsesSymbol Definitions Command/Response Table for SIS CommandsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description CommandSerial port configuration Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software CrossPoint 300 Matrix Switchers Matrix SoftwareComm port selection window Using the softwareMatrix Software, cont’d Extron Matrix Switchers Control Program window no tiesSample program window with ties Updating the firmwareOpen window CrossPoint 300 Matrix Switchers Matrix Software File menu Windows buttons, drop boxes, and trashWindows menus Status window Tools menuPreferences menu Audio-input Configure selectionButton-Label Generator Using emulation modeUsing the help system 13 Extron’s Button-Label Generator window AAppendix a ReferenceInformation,co t’d SpecificationsCrossPoint 300 Matrix Switchers Reference Information Sync Reference Information, cont’d Control/remote switcherIncluded parts Optional accessoriesPart Numbers CrossPoint 300 part numbersButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C