Extron electronic 124, 84, 1616, 1212, 168, 128, 816, 88 manual Tools menu, Status window

Page 91

Tools menu

Assign device icons — Displays the complete set of input and output device icons. You can drag any of these icons to the input and output boxes.

Edit device palette — Allows you to add your own device icon graphics.

Audio-Input gain settings — Displays the audio gain level setting for a single input or for all inputs and allows you to change it. The level is expressed as the magnitude (number of decibels) and polarity (positive, gain or negative, attenuation) of the audio adjustment.

Mute-Outputs settings — Displays the Mute Adjust screen, from which you can mute video and/or audio for each output.

Update firmware — Allows you to replace the firmware that is coded on the switcher’s control board without taking the switcher out of service, opening the switcher enclosure, and replacing the firmware chip set. See “Updating the firmware” on page 5-5.

Hardware status — Provides an overall view of the status of the matrix switcher, including the power supply status and the individual voltages, the temperature status, the Remote RS-232/RS-422 port configuration, and the installed and updated firmware status (figure 5-9).

Figure 5-9 — Status window

Name presets — Allows you to assign a name to each of the 16 memory presets.

Preset names are limited to 12 upper- and lower-case alphanumeric characters and the {space} + _ and / characters.

The following characters are invalid in preset names: ~ @ = ‘ [ ] { } < > ’

“ ; : \ and ?.

Show RS-232 strings — Displays the ASCII commands that are used by the current configuration. You can refer to these for RS-232/RS-422 programming.

Initialize — Initializes and clears any or all of the following: ties, presets, audio configuration, preset titles, I/O names, and I/O icons.

CrossPoint 300 Matrix Switchers • Matrix Software

5-9

Image 91

Contents CrossPoint 300 Series Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschCrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix SwitchersQS-2 CrossPoint 300 Matrix Switchers Quick Start Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset View, adjust the audio levelTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About this Manual About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction Introductiontroduction, cont’dExtron CrossPoint 300 128 HVA DefinitionsIntroduction, cont’d FeaturesCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two UL requirements Installationstallation, cont’dMounting the Switcher CrossPoint 300 Matrix Switchers InstallationShows the CrossPoint 300 128 HVA Connections and Rear Panel FeaturesRgbhv input and output Installation, cont’dAudio input and output HVA models only Typical audio connectors Remote RS-232/RS-422 port Reset buttonPower Sync termination switchesFront panel configuration port Front Panel Configuration PortCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three CrossPoint 300 Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Input and output buttons DefinitionsControl buttons Operation, cont’dCrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel OperationsCreating a configuration Power indicationsClear all selections Example 1 Creating a set of video and audio tiesExample 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio29 Select Rgbhv and audio 31 Unmute the outputs Using global presetsLED blinks figure Example 6 Saving a presetPress and release the Preset button figure Example 7 Recalling a preset39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models42 Clear all selections Example 8 Viewing and adjusting an input audio levelAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA modelsReading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volumeAudio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and modePower Performing a system reset from the front panelSelecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panelPerforming a hard reset from the rear panel Optimizing the Audio HVA SwitchersPlasma display S-video problem TroubleshootingGeneral checks Worksheet example 1 Entering system equipment Configuration WorksheetsWorksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration66 Worksheet example 3 Test configuration Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetThis page was intentionally left blank Four Rear panel Remote port CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Serial PortsFront panel Configuration port Host-to-Switcher InstructionsProgrammer’s Guide, cont’d Switcher-Initiated MessagesUsing the Command/Response Table Switcher Error ResponsesSymbol Definitions Command/Response Table for SIS CommandsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description CommandSerial port configuration Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software CrossPoint 300 Matrix Switchers Matrix SoftwareComm port selection window Using the softwareMatrix Software, cont’d Extron Matrix Switchers Control Program window no tiesSample program window with ties Updating the firmwareOpen window CrossPoint 300 Matrix Switchers Matrix Software Windows menus Windows buttons, drop boxes, and trashFile menu Status window Tools menuPreferences menu Audio-input Configure selectionUsing the help system Using emulation modeButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a CrossPoint 300 Matrix Switchers Reference Information SpecificationsReferenceInformation,co t’d Sync Reference Information, cont’d Control/remote switcherIncluded parts Optional accessoriesPart Numbers CrossPoint 300 part numbersButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C