Extron electronic 816, 84, 1616, 1212, 124, 168, 128, 88 manual Matrix Software, cont’d

Page 86

Matrix Software, cont’d

2.	Choose either the comm port that is connected to the matrix switcher’s serial
	port or Emulate.

Although IP [LAN] is available for selection, the switcher does not have an Ethernet port. Do not select IP [LAN].

If you selected a comm port, check the baud rate displayed in the comm port selection window. If you need to change the baud rate, click on the Baud button and double-click on the desired baud rate.

Available rates are 9600, 19200, 38400, and 115200. The default is 9600.

The switcher can operate at 9600, 19200, 38400, or 115200 baud rates. See “Selecting the rear panel Remote port protocol and baud rate” in chapter 3, “Operation”, to identify the selected baud rate from the front panel.

Click Ok and proceed to step 3.

If you selected Emulate, click Ok and see “Using emulation mode” on page 5-11.

3. The Extron Matrix Switchers Control Program window (figure 5-4 and figure 5-5) appears. The window displays the current configuration of the attached matrix.

Figure 5-4 — Extron Matrix Switchers Control Program window (no ties)

•To set up audio in follow mode (audio and video have the same tie configuration), select the Follow box at the bottom of the window. To set up audio in breakaway mode (audio and video have different tie configurations), deselect the Follow box.

•To make the control program easier to use, assign a device icon to each input and output. Click on a box that represents an input or output, and drag the desired icon onto the box from the icon palette that appears.

•To create a tie, drag an input box to one or more output boxes. To remove a tie, drag the output box to its tied input box or to the trash can.

•For display of information on a specific input or output device, position the cursor over that device in the control program window. The program opens a window that details the connections to that device and the audio level.

5-4 CrossPoint 300 Matrix Switchers • Matrix Software

Image 86

Contents Matrix Switchers CrossPoint 300 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint 300 Matrix Switchers CrossPoint 300 Matrix Switchers Quick Start QS-1View, adjust the audio level Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset QS-2 CrossPoint 300 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction About this ManualDefinitions Extron CrossPoint 300 128 HVAFeatures Introduction, cont’dCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two CrossPoint 300 Matrix Switchers Installation Installationstallation, cont’dMounting the Switcher UL requirementsConnections and Rear Panel Features Shows the CrossPoint 300 128 HVAAudio input and output HVA models only Installation, cont’dRgbhv input and output Typical audio connectors Reset button Remote RS-232/RS-422 portSync termination switches PowerFront Panel Configuration Port Front panel configuration portCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint 300 Matrix Switchers Operation Definitions Input and output buttonsOperation, cont’d Control buttonsCrossPoint 300 Matrix Switchers Operation Controls Front Panel Operations Front panel security lockoutsPower indications Creating a configurationExample 1 Creating a set of video and audio ties Clear all selectionsPress and release the Enter button figure Example 2 Adding a tie to a set of video and audio ties10 Clear all selections Press and release the Enter button figure Example 3 Removing a tie from a set of video and audio ties16 Clear all selections 19 Deselect the output Viewing a configuration 22 Clear all selections23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output29 Select Rgbhv and audio Using global presets 31 Unmute the outputsExample 6 Saving a preset LED blinks figureExample 7 Recalling a preset Press and release the Preset button figure39 Select the preset Viewing and adjusting the input audio level HVA models CrossPoint 300 Series SwitcherExample 8 Viewing and adjusting an input audio level 42 Clear all selectionsAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Viewing and adjusting the output volume HVA models Press and release the Audio button figurePush Esc button nineteen times 10% + 191.5% = 38.5% volume Reading the displayed valueAudio output volume settings Example 9 Viewing and adjusting an output volume level 49 Clear all selections51 Select output Setting the front panel locks Executive modes 54 Volume display on a 16-output-button switcherSelecting Lock mode 2 or toggling between mode 2 and mode 56 Toggle front panel lock on or offPerforming a system reset from the front panel PowerControl Control I/O Enter Preset View ESC Rgbhv Audio Selecting the rear panel Remote port protocol and baud rate60 RS-232/RS-422 and baud rate selection Performing a system reset from the rear panel Rear Panel OperationsOptimizing the Audio HVA Switchers Performing a hard reset from the rear panelGeneral checks TroubleshootingPlasma display S-video problem Configuration Worksheets Worksheet example 1 Entering system equipment65 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration 66 Worksheet example 3 Test configurationMatrix Switchers Configuration Worksheet Preset #This page was intentionally left blank Four Serial Ports CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Rear panel Remote portHost-to-Switcher Instructions Front panel Configuration portSwitcher-Initiated Messages Programmer’s Guide, cont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table for SIS Commands Symbol DefinitionsCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Command Response Additional descriptionSerial port configuration Five CrossPoint 300 Matrix Switchers Matrix Software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dUsing the software Comm port selection windowExtron Matrix Switchers Control Program window no ties Matrix Software, cont’dUpdating the firmware Sample program window with tiesOpen window CrossPoint 300 Matrix Switchers Matrix Software File menu Windows buttons, drop boxes, and trashWindows menus Tools menu Status windowAudio-input Configure selection Preferences menuButton-Label Generator Using emulation modeUsing the help system 13 Extron’s Button-Label Generator window AAppendix a ReferenceInformation,co t’d SpecificationsCrossPoint 300 Matrix Switchers Reference Information Sync Control/remote switcher Reference Information, cont’dCrossPoint 300 part numbers Optional accessoriesPart Numbers Included partsButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C