Extron electronic 168, 84, 1616, 1212, 124, 128 Performing a system reset from the front panel, Power

Page 60

Operation, cont’d

Performing a system reset from the front panel

The front panel reset is identical to the rear panel system reset (see “Performing a system reset from the rear panel” on page 3-39) and to the Esc ZXXX SIS command (see chapter 4, “Programmer’s Guide”). A system reset:

•Clears all ties and presets

•Clears all video and audio mutes

•HVA switchers — Sets all input audio levels to unity gain (+0 dB)

Reset the switcher to the factory default settings by pressing and holding the RGBHV button and Audio button while you apply AC power to the switcher (figure 3-58).

System reset does not replace user-installed firmware upgrades.

Press and hold the RGBHV and Audio buttons while you apply power to the switcher.

I/O

RGBHV AUDIO

Power

The switcher’s LEDs blink and then go dark.

Continue to hold the RGBHV and Audio buttons until all input and output LEDs return to the unlit state and the RGBHV and Audio LEDs turn on.

Release the RGBHV and Audio buttons.

Figure 3-58 — System reset

3-36 CrossPoint 300 Matrix Switchers • Operation

Image 60

Contents Matrix Switchers CrossPoint 300 SeriesSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint 300 Matrix Switchers CrossPoint 300 Matrix Switchers Quick Start QS-1Quick Start CrossPoint 300 Matrix Switchers, cont’d Save or recall a presetView, adjust the audio level QS-2 CrossPoint 300 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About the Matrix Switchers CrossPoint 300 Matrix Switchers IntroductionIntroductiontroduction, cont’d About this ManualDefinitions Extron CrossPoint 300 128 HVAFeatures Introduction, cont’dCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two Installationstallation, cont’d Mounting the SwitcherCrossPoint 300 Matrix Switchers Installation UL requirementsConnections and Rear Panel Features Shows the CrossPoint 300 128 HVAInstallation, cont’d Rgbhv input and outputAudio input and output HVA models only Typical audio connectors Reset button Remote RS-232/RS-422 portSync termination switches PowerFront Panel Configuration Port Front panel configuration portCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Front Panel Controls and Indicators CrossPoint 300 Matrix Switchers OperationOperationeration, cont’d Definitions Input and output buttonsOperation, cont’d Control buttonsCrossPoint 300 Matrix Switchers Operation Controls Front Panel Operations Front panel security lockoutsPower indications Creating a configurationExample 1 Creating a set of video and audio ties Clear all selectionsPress and release the Enter button figure Example 2 Adding a tie to a set of video and audio ties10 Clear all selections Press and release the Enter button figure Example 3 Removing a tie from a set of video and audio ties16 Clear all selections 19 Deselect the output Viewing a configuration 22 Clear all selections23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output29 Select Rgbhv and audio Using global presets 31 Unmute the outputsExample 6 Saving a preset LED blinks figureExample 7 Recalling a preset Press and release the Preset button figure39 Select the preset Viewing and adjusting the input audio level HVA models CrossPoint 300 Series SwitcherExample 8 Viewing and adjusting an input audio level 42 Clear all selectionsAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Viewing and adjusting the output volume HVA models Press and release the Audio button figurePush Esc button nineteen times 10% + 191.5% = 38.5% volume Reading the displayed valueAudio output volume settings Example 9 Viewing and adjusting an output volume level 49 Clear all selections51 Select output Setting the front panel locks Executive modes 54 Volume display on a 16-output-button switcherSelecting Lock mode 2 or toggling between mode 2 and mode 56 Toggle front panel lock on or offPerforming a system reset from the front panel PowerControl Control I/O Enter Preset View ESC Rgbhv Audio Selecting the rear panel Remote port protocol and baud rate60 RS-232/RS-422 and baud rate selection Performing a system reset from the rear panel Rear Panel OperationsOptimizing the Audio HVA Switchers Performing a hard reset from the rear panelTroubleshooting Plasma display S-video problemGeneral checks Configuration Worksheets Worksheet example 1 Entering system equipment65 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration 66 Worksheet example 3 Test configurationMatrix Switchers Configuration Worksheet Preset #This page was intentionally left blank Four CrossPoint 300 Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSerial Ports Rear panel Remote portHost-to-Switcher Instructions Front panel Configuration portSwitcher-Initiated Messages Programmer’s Guide, cont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table for SIS Commands Symbol DefinitionsCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Command Response Additional descriptionSerial port configuration Five Matrix Switchers Control Program Installing the softwareCrossPoint 300 Matrix Switchers Matrix Software MatrixSoftware,cont’dUsing the software Comm port selection windowExtron Matrix Switchers Control Program window no ties Matrix Software, cont’dUpdating the firmware Sample program window with tiesOpen window CrossPoint 300 Matrix Switchers Matrix Software Windows buttons, drop boxes, and trash Windows menusFile menu Tools menu Status windowAudio-input Configure selection Preferences menuUsing emulation mode Using the help systemButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a Specifications CrossPoint 300 Matrix Switchers Reference InformationReferenceInformation,co t’d Sync Control/remote switcher Reference Information, cont’dOptional accessories Part NumbersCrossPoint 300 part numbers Included partsButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C