Extron electronic 168, 84, 1616, 1212, 124, 128, 816, 88 manual Operation, cont’d, Control buttons

Page 28

Operation, cont’d

3Input and output label windows — These translucent panels can be removed and replaced to insert labels behind the panels. To remove a panel, insert the Phillips-head end of a Tweeker or small Phillips-head screwdriver into the hole in one end of the panel, and gently slide the tab at the edge of the panel out of the recess in the switcher housing.

Input and output labels can be created easily with Extron’s button label generator software, which ships with every Extron Matrix Switcher, or with any Brother® P-Touch™labeler. Each input and output can be labeled with names, alphanumeric characters, or even color bitmaps for easy and intuitive input and output selection (figure 3-3). See chapter 5, “Matrix Software”, for details on using the label software.

Rack DVD (ISS 506)

INPUTS

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3-3 — Sample label

Control buttons

4Enter button and LED — The Enter button and LED have three primary functions (•) and four secondary (❏) functions:

•Saves changes that you make on the front panel. To create a simple configuration:

1. Specify RGBHV, audio, or both (see I/O selection buttons [ 8 ] and [ 9 ])

2. Press the desired input button ( 1 )

3. Press the desired output button(s) ( 2 )

4. Press the Enter button.

•Indicates that a potential tie has been created but not saved.

•Indicates that a global preset has been selected to be saved or recalled but that the preset action has not been accomplished.

❏With the Preset, View, and Esc buttons, selects Serial Port Configuration mode. See “Selecting the rear panel Remote port protocol and baud rate” on page 3-37.

❏Selects 9600 baud for the RS-232/RS-422 port in Serial Port Configuration mode. See “Selecting the rear panel Remote port protocol and baud rate” on page 3-37.

❏Indicates that the RS-232/RS-422 port is set to 9600 baud in Serial Port Configuration mode. See “Selecting the rear panel Remote port protocol and baud rate” on page 3-37.

❏With the RGBHV and Audio buttons, select front panel security lockout mode 2 or toggle between mode 0 (unlocked) and mode 2. See “Setting the front panel locks (Executive modes)” on page 3-34.

3-4 CrossPoint 300 Matrix Switchers • Operation

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Matrix Switchers CrossPoint 300 SeriesSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint 300 Matrix Switchers CrossPoint 300 Matrix Switchers Quick Start QS-1Quick Start CrossPoint 300 Matrix Switchers, cont’d Save or recall a presetView, adjust the audio level QS-2 CrossPoint 300 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About the Matrix Switchers CrossPoint 300 Matrix Switchers IntroductionIntroductiontroduction, cont’d About this ManualDefinitions Extron CrossPoint 300 128 HVAFeatures Introduction, cont’dCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two Installationstallation, cont’d Mounting the SwitcherCrossPoint 300 Matrix Switchers Installation UL requirementsConnections and Rear Panel Features Shows the CrossPoint 300 128 HVARgbhv input and output Installation, cont’dAudio input and output HVA models only Typical audio connectors Reset button Remote RS-232/RS-422 portSync termination switches PowerFront Panel Configuration Port Front panel configuration portCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three CrossPoint 300 Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Definitions Input and output buttonsOperation, cont’d Control buttonsCrossPoint 300 Matrix Switchers Operation Controls Front Panel Operations Front panel security lockoutsPower indications Creating a configurationExample 1 Creating a set of video and audio ties Clear all selectionsPress and release the Enter button figure Example 2 Adding a tie to a set of video and audio ties10 Clear all selections Press and release the Enter button figure Example 3 Removing a tie from a set of video and audio ties16 Clear all selections 19 Deselect the output Viewing a configuration 22 Clear all selections23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output29 Select Rgbhv and audio Using global presets 31 Unmute the outputsExample 6 Saving a preset LED blinks figureExample 7 Recalling a preset Press and release the Preset button figure39 Select the preset Viewing and adjusting the input audio level HVA models CrossPoint 300 Series SwitcherExample 8 Viewing and adjusting an input audio level 42 Clear all selectionsAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Viewing and adjusting the output volume HVA models Press and release the Audio button figurePush Esc button nineteen times 10% + 191.5% = 38.5% volume Reading the displayed valueAudio output volume settings Example 9 Viewing and adjusting an output volume level 49 Clear all selections51 Select output Setting the front panel locks Executive modes 54 Volume display on a 16-output-button switcherSelecting Lock mode 2 or toggling between mode 2 and mode 56 Toggle front panel lock on or offPerforming a system reset from the front panel PowerControl Control I/O Enter Preset View ESC Rgbhv Audio Selecting the rear panel Remote port protocol and baud rate60 RS-232/RS-422 and baud rate selection Performing a system reset from the rear panel Rear Panel OperationsOptimizing the Audio HVA Switchers Performing a hard reset from the rear panelPlasma display S-video problem TroubleshootingGeneral checks Configuration Worksheets Worksheet example 1 Entering system equipment65 Worksheet example 2 Status meeting configuration Worksheet example 2 Drawing tiesWorksheet example 3 Test configuration 66 Worksheet example 3 Test configurationMatrix Switchers Configuration Worksheet Preset #This page was intentionally left blank Four CrossPoint 300 Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSerial Ports Rear panel Remote portHost-to-Switcher Instructions Front panel Configuration portSwitcher-Initiated Messages Programmer’s Guide, cont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table for SIS Commands Symbol DefinitionsCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Command Response Additional descriptionSerial port configuration Five Matrix Switchers Control Program Installing the softwareCrossPoint 300 Matrix Switchers Matrix Software MatrixSoftware,cont’dUsing the software Comm port selection windowExtron Matrix Switchers Control Program window no ties Matrix Software, cont’dUpdating the firmware Sample program window with tiesOpen window CrossPoint 300 Matrix Switchers Matrix Software Windows menus Windows buttons, drop boxes, and trashFile menu Tools menu Status windowAudio-input Configure selection Preferences menuUsing the help system Using emulation modeButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a CrossPoint 300 Matrix Switchers Reference Information SpecificationsReferenceInformation,co t’d Sync Control/remote switcher Reference Information, cont’dOptional accessories Part NumbersCrossPoint 300 part numbers Included partsButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C
Top Page Image Contents