Extron electronic 1616, 84 Example 1 Creating a set of video and audio ties, Clear all selections

Page 33

Example 1: Creating a set of video and audio ties

The following steps show an example in which input 5 is tied to outputs 3, 4, and 8. The steps show the front panel indications that result from your actions.

This example assumes that there are no ties in the current configuration.

1.

Press and release the Esc button (figure 3-4).

Press the Esc button to clear all selections.

CONTROL

The LED blinks once.

ENTER PRESET VIEW ESC

Figure 3-4 — Clear all selections

2. To select video and audio for the tie, if necessary, press and release the RGBHV button and the Audio button until the LEDs light (figure 3-5).

I/O

RGBHV AUDIO

Press the RGBHV button to toggle on and off.

The LED lights when selected.

Press the Audio button to toggle on and off.

The LED lights when selected.

Figure 3-5 — Select RGBHV and audio

3.

Press and release the input 5 button (figure 3-6).

Press and release the Input 5 button.

3 4

INPUTS

5 6 7

The LED lights.

Figure 3-6 — Select an input

4.

Press and release the output 3, output 4, and output 8 buttons (figure 3-7).

The entire set of ties can be canceled at this point by pressing and releasing the Esc button. The Esc LED flashes once.

CrossPoint 300 Matrix Switchers • Operation

3-9

Image 33
Contents CrossPoint 300 Series Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolCrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix SwitchersSave or recall a preset Quick Start CrossPoint 300 Matrix Switchers, cont’dView, adjust the audio level QS-2 CrossPoint 300 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One CrossPoint 300 Matrix Switchers Introduction About the Matrix SwitchersIntroductiontroduction, cont’d About this ManualExtron CrossPoint 300 128 HVA DefinitionsIntroduction, cont’d FeaturesCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two Mounting the Switcher Installationstallation, cont’dCrossPoint 300 Matrix Switchers Installation UL requirementsShows the CrossPoint 300 128 HVA Connections and Rear Panel FeaturesInstallation, cont’d Rgbhv input and outputAudio input and output HVA models only Typical audio connectors Remote RS-232/RS-422 port Reset buttonPower Sync termination switchesFront panel configuration port Front Panel Configuration PortCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Front Panel Controls and Indicators CrossPoint 300 Matrix Switchers OperationOperationeration, cont’d Input and output buttons DefinitionsControl buttons Operation, cont’dCrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel OperationsCreating a configuration Power indicationsClear all selections Example 1 Creating a set of video and audio tiesExample 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio29 Select Rgbhv and audio 31 Unmute the outputs Using global presetsLED blinks figure Example 6 Saving a presetPress and release the Preset button figure Example 7 Recalling a preset39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models42 Clear all selections Example 8 Viewing and adjusting an input audio levelAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA modelsReading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volumeAudio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and modePower Performing a system reset from the front panelSelecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panelPerforming a hard reset from the rear panel Optimizing the Audio HVA SwitchersTroubleshooting Plasma display S-video problemGeneral checks Worksheet example 1 Entering system equipment Configuration WorksheetsWorksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration66 Worksheet example 3 Test configuration Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetThis page was intentionally left blank Four Programmer’ser’sGuide,Guidecont’d CrossPoint 300 Matrix Switchers Programmer’s GuideSerial Ports Rear panel Remote portFront panel Configuration port Host-to-Switcher InstructionsProgrammer’s Guide, cont’d Switcher-Initiated MessagesUsing the Command/Response Table Switcher Error ResponsesSymbol Definitions Command/Response Table for SIS CommandsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description CommandSerial port configuration Five Installing the software Matrix Switchers Control ProgramCrossPoint 300 Matrix Switchers Matrix Software MatrixSoftware,cont’dComm port selection window Using the softwareMatrix Software, cont’d Extron Matrix Switchers Control Program window no tiesSample program window with ties Updating the firmwareOpen window CrossPoint 300 Matrix Switchers Matrix Software Windows buttons, drop boxes, and trash Windows menusFile menu Status window Tools menuPreferences menu Audio-input Configure selectionUsing emulation mode Using the help systemButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a Specifications CrossPoint 300 Matrix Switchers Reference InformationReferenceInformation,co t’d Sync Reference Information, cont’d Control/remote switcherPart Numbers Optional accessoriesCrossPoint 300 part numbers Included partsButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C