Extron electronic 88, 84, 1616, 1212, 124, 168, 128, 816 Viewing a configuration, Clear all selections

Page 39

Viewing a configuration

The current configuration can be viewed using the front panel buttons. The View-onlymode prevents inadvertent changes to the current configuration. View-onlymode also provides a way to mute video and audio outputs (see “Muting and unmuting video and/or audio” on page 3-18.

View the current configuration as follows:

1.	Press the Esc button to clear any input LEDs, output LEDs, or control LEDs
	that are lit.
2.	Press and release the View button. All of the LEDs for outputs that are not
	tied light.
3.	Select video, audio, or both to view by pressing the RGBHV button and/or
	the Audio button.
4.	Select the desired input or output(s) whose ties you wish to view by pressing

the input and output buttons.

• When you enter View-onlymode, the output LEDs light for all outputs without ties. Likewise, when an output button for which there are no ties is pushed, the output LEDs turn on for all outputs without ties.

•To see all ties of the current configuration, press and release each input and output button, one at a time, with the RGBHV LED and the Audio LED lit.

•In View-onlymode, you can view video and audio, video-only, or audio- only ties. Pressing and releasing the RGBHV button and the Audio button toggles each on and off.

•After 30 seconds of front panel inactivity, View-onlymode automatically deselects.

Example 4: Viewing video and audio, audio-only, and video-only ties

The following steps show an example of viewing the video and audio, audio-only, and video-only ties in the current configuration. The steps show the front panel indications that result from your action.

This example assumes that you have performed example 1, example 2, and example 3.

1.	Press and release the Esc button (figure 3-22).

Press the Esc button to clear all selections.

CONTROL

The LED blinks once.

ENTER PRESET VIEW ESC

Figure 3-22 — Clear all selections

CrossPoint 300 Matrix Switchers • Operation 3-15

Image 39

Contents CrossPoint 300 Series Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschCrossPoint 300 Matrix Switchers Quick Start QS-1 Quick Start CrossPoint 300 Matrix SwitchersQS-2 CrossPoint 300 Matrix Switchers Quick Start Quick Start CrossPoint 300 Matrix Switchers, cont’dSave or recall a preset View, adjust the audio levelTable of Contents Table of Contents, cont’d CrossPoint 300 Matrix Switchers Table of Contents Iii Iv CrossPoint 300 Matrix Switchers Table of Contents One About this Manual About the Matrix SwitchersCrossPoint 300 Matrix Switchers Introduction Introductiontroduction, cont’dExtron CrossPoint 300 128 HVA DefinitionsIntroduction, cont’d FeaturesCrossPoint 300 Matrix Switchers Introduction This page was intentionally left blank Two UL requirements Installationstallation, cont’dMounting the Switcher CrossPoint 300 Matrix Switchers InstallationShows the CrossPoint 300 128 HVA Connections and Rear Panel FeaturesInstallation, cont’d Rgbhv input and outputAudio input and output HVA models only Typical audio connectors Remote RS-232/RS-422 port Reset buttonPower Sync termination switchesFront panel configuration port Front Panel Configuration PortCrossPoint 300 Matrix Switchers Installation Installation, cont’d Three Front Panel Controls and Indicators CrossPoint 300 Matrix Switchers OperationOperationeration, cont’d Input and output buttons DefinitionsControl buttons Operation, cont’dCrossPoint 300 Matrix Switchers Operation Controls Front panel security lockouts Front Panel OperationsCreating a configuration Power indicationsClear all selections Example 1 Creating a set of video and audio tiesExample 2 Adding a tie to a set of video and audio ties Press and release the Enter button figure10 Clear all selections Example 3 Removing a tie from a set of video and audio ties Press and release the Enter button figure16 Clear all selections 19 Deselect the output 22 Clear all selections Viewing a configuration23 Select Rgbhv or video and audio 25 Deselect Rgbhv to view audio ties only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio29 Select Rgbhv and audio 31 Unmute the outputs Using global presetsLED blinks figure Example 6 Saving a presetPress and release the Preset button figure Example 7 Recalling a preset39 Select the preset CrossPoint 300 Series Switcher Viewing and adjusting the input audio level HVA models42 Clear all selections Example 8 Viewing and adjusting an input audio levelAudio gain and attenuation settings 45 Level display on a 16-output-LED switcher 46 Adjust the input audio level Press and release the Audio button figure Viewing and adjusting the output volume HVA modelsReading the displayed value Push Esc button nineteen times 10% + 191.5% = 38.5% volumeAudio output volume settings 49 Clear all selections Example 9 Viewing and adjusting an output volume level51 Select output 54 Volume display on a 16-output-button switcher Setting the front panel locks Executive modes56 Toggle front panel lock on or off Selecting Lock mode 2 or toggling between mode 2 and modePower Performing a system reset from the front panelSelecting the rear panel Remote port protocol and baud rate Control Control I/O Enter Preset View ESC Rgbhv Audio60 RS-232/RS-422 and baud rate selection Rear Panel Operations Performing a system reset from the rear panelPerforming a hard reset from the rear panel Optimizing the Audio HVA SwitchersTroubleshooting Plasma display S-video problemGeneral checks Worksheet example 1 Entering system equipment Configuration WorksheetsWorksheet example 2 Drawing ties 65 Worksheet example 2 Status meeting configuration66 Worksheet example 3 Test configuration Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetThis page was intentionally left blank Four Rear panel Remote port CrossPoint 300 Matrix Switchers Programmer’s GuideProgrammer’ser’sGuide,Guidecont’d Serial PortsFront panel Configuration port Host-to-Switcher InstructionsProgrammer’s Guide, cont’d Switcher-Initiated MessagesUsing the Command/Response Table Switcher Error ResponsesSymbol Definitions Command/Response Table for SIS CommandsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands Cont’d Audio volume adjustment settings Save, recall, and directly write presets Response Additional description CommandSerial port configuration Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software CrossPoint 300 Matrix Switchers Matrix SoftwareComm port selection window Using the softwareMatrix Software, cont’d Extron Matrix Switchers Control Program window no tiesSample program window with ties Updating the firmwareOpen window CrossPoint 300 Matrix Switchers Matrix Software Windows buttons, drop boxes, and trash Windows menusFile menu Status window Tools menuPreferences menu Audio-input Configure selectionUsing emulation mode Using the help systemButton-Label Generator 13 Extron’s Button-Label Generator window AAppendix a Specifications CrossPoint 300 Matrix Switchers Reference InformationReferenceInformation,co t’d Sync Reference Information, cont’d Control/remote switcherIncluded parts Optional accessoriesPart Numbers CrossPoint 300 part numbersButton Labels Figure A-1 Button label blanks, 16-button strips Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C