Extron electronic HSA 822 user manual Installation, cont’d Cabling and Installing the AAPs

Page 11

Installation, cont’d

Cabling and Installing the AAPs

The space behind the AAP panel is limited. The online Connectivity Configurator, available at www.extron.com, offers guidance as to the fit of AAPs into this space.

Extron’s various single space and double space AAP devices, including the various RGB 580xi AAPs, can be mounted to the HSA 822. See appendix A, “Reference Information”, for RGB 580xi AAP part numbers.

The screws for installing an AAP are built into its AAP panel, so no additional screws are needed.

Ensure that AC power is disconnected before

servicing the HSA unit.

1. Remove the top and bottom screws on the right and left

sides of the AAP panel (figure 2-4). Retain the screws. Lift

the panel away from the enclosure as far as the connected

cables allow and then allow the panel to dangle,

supported by its connected cables.

Remove two screws ea. side.

Remove panel.

HSA822

Replacement Face Plate

Screws (4) Under Enclosure

Figure 2-4 — Removing the AAP panel from an HSA 822

 

 

The center screws on each side of the AAP panel do not

 

 

fasten the AAP panel in place. They secure the

 

 

AC power outlet.

 

 

Ensure that the edges of the AAP panels do not scratch

 

 

 

 

the finished surface of the top panel flange when

 

 

removing the panels.

2.

Cable the rear of the AAPs before fastening the AAPs to

 

the AAP panel. Route the cables through the hole in the

 

underside of the surface mount enclosure and connect

 

them to the rear of the AAPs. If applicable, refer to the

 

cabling information in the documentation for the AAP.

3.

Insert each of the AAP’s screws through the holes in the

AAP Panel

INP

 

 

 

 

 

S

UT

 

 

 

 

 

ELE

CO

 

A

 

 

 

CT

MP

UD

IO

 

 

 

UTER

 

#4-40 Nut w/ Captive Washer

Cable

HSA

822

 

RGB 580xi SI AAP

AAP opening of the HSA AAP panel. Secure each AAP to

the panel with the provided captive washers and #4-40

nuts (figure 2-5).

Figure 2-5 — Mounting an AAP device on the AAP panel

4. Replace the AAP panel in the surface mount enclosure and secure it in place with the screws removed in step 1. If you lose an AAP panel screw, four spare screws are stored in the underside of the enclosure.

2-8

HSA 822 Hideaway® Enclosure • Installation

HSA 822 Hideaway® Enclosure • Installation

2-9

Image 11
Contents HSA Hideaway Surface Access EnclosureExtron’s Warranty PrecautionsPage Table of Contents HSA 822 Hideaway Enclosure Table of Contents, cont’dIntroduction About the HSA 822 Hideaway Enclosure IntroductionIntroduction, cont’d InstallationFeatures Preparing the Routing Template InstallationInstallation Overview Assembly to the table with C-clamps figure Other installation surface. Mark the locationPlace the routing template assembly on the table, centered Once the template assembly is positioned properly, secureFinishes Installation, cont’dClean the HSA. Strong solvents will ruin some Do not use isopropyl alcohol or other solvents toInstallation, cont’d Cabling and Installing the AAPs An RJ-11 telephone plug can be connected to the RJ-45 jack Installation, cont’d Cabling the EnclosureBottom panel features Bezels Installation, cont’d Routing the AAP CablesThree Maintenance and ModificationsReplacing an AAP Maintenance and ModificationsRemoving and Replacing the Enclosure Maintenance and Modifications, cont’d Replacing the BezelsMaintenance and Modifications, cont’d Replacing the Gas Lift Platform, the bracket will be floppy atop the gas lift Insert the shaft end of the replacement gas lift throughReconnect the interior AC power cables With the top panel bracket detached from the liftingHeight adjustment locking screw slots Adjusting the height of the top surfaceReference Information Adjusting the top surface levelGeneral SpecificationsReference Information Part NumbersReference Information, cont’d Included Parts Template, Replacement Parts, and AccessoriesInterface Accessories Top Plate DimensionsReference Information, cont’d Packaging for ShipmentFigure B-1 HSA 822 return kit Packaging for ShipmentPackaging for Shipment, Cont’d Figure B-3 Installing protective stripsFigure B-6 Placing the HSA in the shipping carton Packaging for Shipment, Cont’d
Related manuals
Manual 23 pages 6.66 Kb