Extron electronic HSA 822 user manual Installation, cont’d Routing the AAP Cables, Bezels

Page 13

Installation, cont’d

Routing the AAP Cables

The AAP cables must have freedom of movement to permit opening and closing the surface mount enclosure. At the same time, they need to be restrained to prevent their rubbing against the edges of the enclosure cable access hole in the underside of the surface mount enclosure. Rubbing against the cable access hole edges can damage the cables. Route and secure the AAP cables as follows:

1. Open the top panel to extend the AAP cables to their

maximum pull.

Bezels

The HSA 822 ships with RJ-45/RJ-11 connector bezel plug-ins in a variety of colors and a black, blank bezel.

Bezel

To change to a different color RJ-45 connector bezel or if an RJ-45 connector is not needed or desired, replace the connector bezel plug-in on the AAP panel with a bezel of a different color or a blank plug-in. See Replacing the Bezels in chapter 3.

2. Experiment with AAP cable positioning to ensure that the

cables do not rub against the edges of the AAP cable hole

and to ensure that the cable pull does not restrict the

movement of the top panel. Figure 2-9 shows the cables

routed to the side, which proved effective in tests at

Extron.

3.Use tie wraps to secure the AAP cables to the tie-down holes in the clamshell and enclosure in the locations shown on figure 2-9.

View from one side

View from the opposite side

Secure the AAP cables at the circled locations.

Figure 2-9 — HSA 822 AAP cable routing

If no RJ-45 connector is desired, snap the interior RJ-45 cable onto the rear of the blank bezel plug-in (shown at right) to hold it conveniently out of the way. Retain the removed connector bezel plug-in for any possible later use.

Blank Bezel

Plug-in in AAP

Panel

2-12 HSA 822 Hideaway® Enclosure • Installation

HSA 822 Hideaway® Enclosure • Installation 2-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents HSA Hideaway Surface Access EnclosureExtron’s Warranty PrecautionsPage Table of Contents Introduction Table of Contents, cont’dHSA 822 Hideaway Enclosure About the HSA 822 Hideaway Enclosure IntroductionFeatures InstallationIntroduction, cont’d Installation Overview InstallationPreparing the Routing Template Place the routing template assembly on the table, centered Other installation surface. Mark the locationOnce the template assembly is positioned properly, secure Assembly to the table with C-clamps figureClean the HSA. Strong solvents will ruin some Installation, cont’dDo not use isopropyl alcohol or other solvents to FinishesInstallation, cont’d Cabling and Installing the AAPs Bottom panel features Installation, cont’d Cabling the EnclosureAn RJ-11 telephone plug can be connected to the RJ-45 jack Bezels Installation, cont’d Routing the AAP CablesThree Maintenance and ModificationsReplacing an AAP Maintenance and ModificationsRemoving and Replacing the Enclosure Maintenance and Modifications, cont’d Replacing the BezelsMaintenance and Modifications, cont’d Replacing the Gas Lift Reconnect the interior AC power cables Insert the shaft end of the replacement gas lift throughWith the top panel bracket detached from the lifting Platform, the bracket will be floppy atop the gas liftHeight adjustment locking screw slots Adjusting the height of the top surfaceReference Information Adjusting the top surface levelReference Information SpecificationsPart Numbers GeneralInterface Accessories Template, Replacement Parts, and AccessoriesTop Plate Dimensions Reference Information, cont’d Included PartsReference Information, cont’d Packaging for ShipmentFigure B-1 HSA 822 return kit Packaging for ShipmentPackaging for Shipment, Cont’d Figure B-3 Installing protective stripsFigure B-6 Placing the HSA in the shipping carton Packaging for Shipment, Cont’d
Related manuals
Manual 23 pages 6.66 Kb
Top Page Image Contents