ATTO Technology 2200R/D, 3200R, 2100R manual LED Indicator, IEC Power Receptacle and Switch

Page 13

ATTO Technology, Inc.

ATTO FibreBridge Installation & Operation Manual

Power Draw: The maximum power draw is 2 Amps @ 110 Volts for the entire ATTO FC Rack System. When the ATTO FC Rack System has two Power Modules, the entire unit will still draw only 2 Amps @ 110 Volts.

LED Indicator

The green LED indicator on the Power Module will light when the module is correctly installed and the switch is turned on. This LED indicates that power is being drawn from this module and is available on the backplane. A Power Module that is turned on when not installed will not have the LED illuminated. It is not recommended and can be dangerous if the AC power cord is plugged in and the power switch is turned on with an uninstalled Power Module.

IEC Power Receptacle and Switch

The Power Module has one standard IEC320 power receptacle and switch for easy adaptability to different voltage standards throughout the world.

Figure 3.7 Power Module Connector Pinout

Installation and Removal

To install a power module:

Step 1. Make sure the power switch on the rear of the power module is in the off position and the power cord is disconnected.

Step 2. Slide the power module into the rack enclosure until you feel it make contact with the backplane connector. The face of the power module should be flush against the rack enclosure edges.

Step 3. Secure the power module by tightening the two thumb screws (hand tight).

Step 4. Connect the AC power cord to the power module and plug it into an appropriate receptacle.

ATTO Technology, Inc.

- 8 -

Image 13
Contents Atto Technology, Inc Atto FibreBridge Atto Technology, Inc Atto Fibrebridge Benefits and Features Updating the Firmware Within the Fibrebridge Atto Technology, Inc FibreBridge Product Module Description IntroductionFC Rack System Product Description References Fibre Channel TechnologyFibre Channel Switch Support Atto FibreBridge Benefits and FeaturesAtto FibreChain FibreBridge Feature Comparison FeaturePhysical Dimensions Atto FC Rack Enclosure and Power ModulesMounting Cooling Airflow EnvironmentalCooling Fans Power Module Internal Power DistributionIEC Power Receptacle and Switch LED IndicatorInstallation and Removal Atto FC Rack System Installation Considerations Atto FibreBridge Product Module Integration Power RequirementsAtto FibreBridge Power Connector Scsi Ports Fibre Channel PortsFibreChain Ports 2100 model only LED IndicatorsAtto FibreChain Port LEDs 2100R model only Serial Port Ethernet PortFibreBridge2200R/D Front View FibreBridge 2200R/D2200R/D Side view with hole dimensions Cooling and Airflow Power SupplyScsi Fibre Channel PortLED Indicators on FibreBridge 2200R/D Cabling a FibreBridge Quick Installation InstructionsScsi Cabling Scsi Termination Typical Scsi CablesConnector Laser Type ConnectorFibre Channel Cabling Cable LengthGbic Module and Gbic Guide System Gbic Installation InstructionsMedia Interface Adapters MIA Gbic Removal InstructionsPin # Name MIA Installation MIA DB9 ConnectorAtto BridgeTools Graphical Interface Configuration Program FibreBridge ServicesAccessing the Atto FibreBridge over the RS-232 interface Monitoring and Managing the Atto FibreBridgeSetting up the IP Address using the RS-232 port Accessing the Atto FibreBridge over the Ethernet PortAccessing through FTP Atto Technology, Inc What is Serverless Backup? Serverless Backup SupportEnabling Serverless Backup on the FibreBridge General Operation of Serverless BackupTarget Descriptors Segment DescriptorsFlashing the FibreBridge Updating the Firmware Within the FibreBridgeIdentifying the FibreBridge Addressing Scsi DevicesIdentifying the Scsi Devices Connected to the FibreBridge Default Address Translation Addressing Devices Connected to the FibreBridge Appendix a Fibre Channel to Scsi Address MappingScsi Address Components Fibre Channel AddressingFibre Channel World Wide Name WWN Arbitrated Loop Port Address AlpaBit Scsi Architecture Model SAM-2 Logical Unit AddressingPeripheral Device Addressing Method Bit Number Address Address Method Specific DefinitionVirtual Device Addressing Method FibreBridge Default ModeLogical Unit Addressing Method SCSI-3 Inquiry Command SCSI-3 Command Changes for Hierarchical Addressing SupportFibre Channel to Scsi Address Mapping Address DescriptorsSCSI-3 Report LUNs Command What to Expect When Setting Device IDsSetting the ID of the FibreBridge Addressing Connected Scsi DevicesAtto Technology, Inc Scsi Device ID Translated LUN as it appears to the Host Configuration for Consecutive IDsAtto Technology, Inc FCC Standards Appendix B Radio and Television InterferenceCanadian Standards European StandardsFurther results of FCC Testing Maximum Height = 1.582 4.015 cm Maximum Height = 1.272 3.228 cm Figure C-3 Atto FibreBridge 3200R Connector Layout Appendix D Fibre Channel Resources Field Replacement Units FRU Appendix E Fibre Channel AccessoriesMIAs Cables/CopperCables/FibreChain Cables/OpticalCables/SCSI Appendix F How to Contact Atto Technology, Inc