ATTO Technology 2100R, 2200R/D, 3200R manual Maximum Height = 1.272 3.228 cm

Page 54

ATTO Technology, Inc.

ATTO FibreBridge Installation & Operation Manual

Maximum Height

= 1.272” (3.228 cm)

Figure C-2 ATTO FibreBridge 2200R/D and 3200R Product Modules’ Board Layout

ATTO Technology, Inc.

- 49 -

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Atto Technology, Inc Atto FibreBridge Atto Technology, Inc Atto Fibrebridge Benefits and Features Updating the Firmware Within the Fibrebridge Atto Technology, Inc Introduction FibreBridge Product Module DescriptionFC Rack System Product Description Fibre Channel Technology ReferencesAtto FibreBridge Benefits and Features Fibre Channel Switch SupportAtto FibreChain Feature FibreBridge Feature ComparisonAtto FC Rack Enclosure and Power Modules Physical DimensionsMounting Environmental Cooling AirflowCooling Fans Internal Power Distribution Power ModuleLED Indicator IEC Power Receptacle and SwitchInstallation and Removal Atto FC Rack System Installation Considerations Power Requirements Atto FibreBridge Product Module IntegrationAtto FibreBridge Power Connector Fibre Channel Ports Scsi PortsLED Indicators FibreChain Ports 2100 model onlyAtto FibreChain Port LEDs 2100R model only Ethernet Port Serial PortFibreBridge 2200R/D FibreBridge2200R/D Front View2200R/D Side view with hole dimensions Power Supply Cooling and AirflowFibre Channel Port ScsiLED Indicators on FibreBridge 2200R/D Quick Installation Instructions Cabling a FibreBridgeScsi Cabling Typical Scsi Cables Scsi TerminationFibre Channel Cabling ConnectorConnector Laser Type Cable LengthGbic Installation Instructions Gbic Module and Gbic Guide SystemGbic Removal Instructions Media Interface Adapters MIAPin # Name MIA DB9 Connector MIA InstallationAccessing the Atto FibreBridge over the RS-232 interface FibreBridge ServicesAtto BridgeTools Graphical Interface Configuration Program Monitoring and Managing the Atto FibreBridgeAccessing the Atto FibreBridge over the Ethernet Port Setting up the IP Address using the RS-232 portAccessing through FTP Atto Technology, Inc Serverless Backup Support What is Serverless Backup?Target Descriptors General Operation of Serverless BackupEnabling Serverless Backup on the FibreBridge Segment DescriptorsUpdating the Firmware Within the FibreBridge Flashing the FibreBridgeAddressing Scsi Devices Identifying the FibreBridgeIdentifying the Scsi Devices Connected to the FibreBridge Default Address Translation Appendix a Fibre Channel to Scsi Address Mapping Addressing Devices Connected to the FibreBridgeFibre Channel World Wide Name WWN Fibre Channel AddressingScsi Address Components Arbitrated Loop Port Address AlpaScsi Architecture Model SAM-2 Logical Unit Addressing BitBit Number Address Address Method Specific Definition Peripheral Device Addressing MethodFibreBridge Default Mode Virtual Device Addressing MethodLogical Unit Addressing Method Fibre Channel to Scsi Address Mapping SCSI-3 Command Changes for Hierarchical Addressing SupportSCSI-3 Inquiry Command Address DescriptorsSetting the ID of the FibreBridge What to Expect When Setting Device IDsSCSI-3 Report LUNs Command Addressing Connected Scsi DevicesAtto Technology, Inc Configuration for Consecutive IDs Scsi Device ID Translated LUN as it appears to the HostAtto Technology, Inc Canadian Standards Appendix B Radio and Television InterferenceFCC Standards European StandardsFurther results of FCC Testing Maximum Height = 1.582 4.015 cm Maximum Height = 1.272 3.228 cm Figure C-3 Atto FibreBridge 3200R Connector Layout Appendix D Fibre Channel Resources MIAs Appendix E Fibre Channel AccessoriesField Replacement Units FRU Cables/CopperCables/Optical Cables/FibreChainCables/SCSI Appendix F How to Contact Atto Technology, Inc
Top Page Image Contents